Hi All,

In this occasion pls be informed that we want to sell our Fuji line
(CP43-4000 and FIP3E-5000 with 1200 feeders), if someone is interesting,
pls call me. 

Best Regards
Reuven ROKAH 


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ed Popielarski
Sent: Sunday, December 10, 2006 6:36 PM
To: [log in to unmask]
Subject: [TN] Fuji GP-341

Jerry,



It's likely the strain gage sensor has failed and goes "out of range"
(hence
the 0F14 reading). The best way to debug this to break out the
schematics
and an oscilloscope to do a little detective work. The strain gage is
likely
marked with a vendor name and part number in which you can look up the
proper operating parameters.



I hope this helps! Feel free PM me if you have any more questions.



Regards,



Ed Popielarski

QTA Machine

27291 Jardines

Mission Viejo, Ca 92692



Ph: 949-581-6601



WWW.QTA.NET



"Nearly 50% of the population is below average intelligence!"

Me 2006





-----Original Message-----

From: TechNet [mailto:[log in to unmask]] On Behalf Of Jerry Dengler

Sent: Friday, December 08, 2006 2:30 PM

To: [log in to unmask]

Subject: [TN] Fuji GP-341



Hello Fellow Technetters,

=20

I'm having a problem with a Fuji GP-341. =20 It has squeegee pressure
control using a TD-320A comparator.

I cannot get it to measure printing pressure.

On the TD-320A it normally reads "2512" then flips to "oFl4" then back
to
"2512".

If I perform the Printing Pressure Measurement steps from the GP 2/3
operation manual the reading goes to "2767" while the blade is down then
returns to the 2512/oFl4 reading.  After a short delay I get an error
message "PRESS SET L(R) NG" depending on which side I try to measure.

=20

The books do not give much info on this system and Fuji wants me to
register
the machine before technical support.  I wouldn't mind paying Fuji if I
knew
they could solve the problem.  They have not been much help on older
machines lately.

=20

Has anyone come across this before?  I'm hoping the TD-320A just needs
to be
calibrated but I'm not sure.

=20

Thanks for any help you can provide.

=20

Jerry




---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------