Subject: | |
From: | |
Reply To: | |
Date: | Mon, 8 May 2006 15:14:42 -0400 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Victor,
try posting this on Designers Council, they might be able to tell you.
The only restriction I know of is when having V-scored edges, you need a 20 mil keep away for 0.062" thick boards and 0.030" for 0.093" thick. This is to avoid having the tool cutting into the copper.
I guess it all comes down to a minimum dielectric specing, particular to your design.
Regards,
Ioan
-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Victor G. Hernandez
Sent: Monday, May 08, 2006 2:42 PM
To: [log in to unmask]
Subject: Re: [TN] IPC Standard msg4
Susan,
Thanks for sharing the IPC sec/par. I too have experience that some
criterions are not carried forward as Rev is being updated by IPC. It
appears that the IPC STD have been relaxed.
Victor.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Susan Mansilla
Sent: Monday, May 08, 2006 1:21 PM
To: [log in to unmask]
Subject: Re: [TN] IPC Standard msg4
Here is a paragraph from the old IPC-D-275 that provides a measurement.
Could not find a similar para in IPC-2221
5.3.1.4 Edge Spacing Except for edge-board contacts,
the minimum distance between conductive surfaces and the
edge of the finished board shall not be less than the minimum
spacing specified in Table 3-1 plus 0.4 mm [0.016
in]. Printed boards that slide into guides shall have a minimum
external conductor to guide distance of 1.25 mm
Susan Hott
Robisan Lab
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|