Subject: | |
From: | |
Reply To: | |
Date: | Tue, 10 Jan 2006 12:26:26 -0600 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Press-fit (compliant pin) connectors are also often used when a
double-sided SMT design is desired and where one wants to avoid the need
to selectively solder a connector that requires good mechanical
integrity. Performing a double-sided reflow and then simply pressing in
the connectors is a nice, clean process.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Mattson, Jeffrey
Sent: Tuesday, January 10, 2006 10:49 AM
To: [log in to unmask]
Subject: Re: [TN] Press Fit Pins / Compliance Pins
Victor,
Compliant pin connectors are typically used on assemblies that are
difficult to solder. These are usually thick backplanes (.125" - .300"
and up). The heat required to wet and flow solder joints through thick
boards can be detrimental. Compliant contacts are ideal in these
situations. When using compliant contacts,hole size is critical (both
drill and finish.
I know this is a very general answer. What is your application?
Jeff
-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Victor G. Hernandez
Sent: Tuesday, January 10, 2006 11:06 AM
To: [log in to unmask]
Subject: [TN] Press Fit Pins / Compliance Pins
Fellow TechNetters:
Can some one share their experience when is a compliance pins is a
GOOD candidate for a PWB/PCB insertion.
Victor,
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|