Hi Ioan:
I believe that as long as you have a good reflow oven profile that fully activates the acids in the flux and turns them into inert bases that are entrapped by the resins or rosins, they are going no where and cause no problems.
Regards,
Ramon
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ingemar Hernefjord
Sent: Saturday, November 19, 2005 4:29 AM
To: [log in to unmask]
Subject: [TN] SV: [TN] Entrapped flux
We have produced about 500,000 complex RF boards the last years, thousands of vias on each board, never had problem with entrapped flux.
Used in deserts, jungles, mountains, traffic environment, sea, salt, all places.
Such RF boards are impossible to clean 100%, too many pockets. Important
condition: always working or standby, never stored without dessicator bags before mounting.
Inge
-----Ursprungligt meddelande-----
Från: TechNet [mailto:[log in to unmask]] För Tempea, Ioan
Skickat: den 18 november 2005 22:26
Till: [log in to unmask]
Ämne: [TN] Entrapped flux
Technos,
I have sort of rookie questions on the following situation:
when reflowing a DPAK, let's say, and the pad thermal pad has vias, the solder will flow inside the via. If the holes are covered with solder mask on the other side, will flux residue build up at the bottom of the hole, like a void between the solder and the solder mask? Or it will rather stay on the surface?
Or, if the DPAK is printed with a nicely shaped stencil, so that no solder goes into the hole, but this time there is no solder mask covering the hole and I fill the vias from the bottom, manually, can I generate a flux pocket somewhere, or the flux only stays on the surface?
And if the flux, water soluble, is entrapped therefore not washable, will it be corrosive?
You must have guessed the application, RF boards, with all these components that have tons of vias under them, vias that must be filled for max thermal transfer, but the solder shall not go on the other side, because the other side is an exposed plane, etc.
Thanks,
Ioan
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
