TECHNET Archives

November 2005

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
"Chezhian, Krishnan" <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Chezhian, Krishnan
Date:
Mon, 21 Nov 2005 14:53:19 +0800
Content-Type:
text/plain
Parts/Attachments:
text/plain (508 lines)
The flash gold as mentioned by Lee below is an electrolytic process & is
usually plated over nickel & not copper. If it is going to be used for SMT
soldering purpose the 2microinches of flash gold is good enough, but if it
is for wire bonding or contact fingers then the gold thickness is too
low.....



Thanks,

Krishnan

SANMINA-SCI

Quality Assurance / NPI Manager

E-mail: [log in to unmask]

Phone (Off): 082-363000 Ext. 1602

Mobile: 012-8888-379

-----Original Message-----
From: Anil Kher [mailto:[log in to unmask]]
Sent: Monday, November 21, 2005 2:32 PM
To: [log in to unmask]
Subject: Re: [TN] best plated surface finish



Dear lee



I  understand the new version of flash gold is direct immersion on copper.



Is that correct. Has it been tested extensively?



Anil Kher

micro interconnexion pvt. ltd

D3-12A, Corlim Industrial Estate

Corlim, Ilhas , Goa , India 403110

tel: 91-832-2284209/337. fax 2284209/2285271

e mail: [log in to unmask]

Leaders in Gold plated PCBs - selective/ cob

an ISO 9001-2000 Company





-----Original Message-----

From: Lee parker [mailto:[log in to unmask]]

Sent: Monday, November 21, 2005 1:16 AM

Subject: Re: best plated surface finish



Jerry



Hope all is well with you.



I did not mention immersion silver since it has been discussed at length in

this forum and most are ware that I am a huge advocate of immersion silver

going bask to 1995 when I installed the first such line in North America at

the AT&T plant in Richmond.



I mentioned Flash Gold because it is a relatively new coating (in its

present format) and is just beginning to catch the attention of the OEMs.



Best regards



Lee



J. Lee Parker, Ph.D.

JLP Consultants LLC

804 779 3389

----- Original Message -----

  From: Gerald Gagnon<mailto:[log in to unmask]>

  To: [log in to unmask]<mailto:[log in to unmask]>

  Sent: Friday, November 18, 2005 6:28 PM

  Subject: Re: [TN] best plated surface finish





  Lee



  Kudos from a long time lurker......



  You're absolutely correct. Many many years of OEM experience with this

  finish. Lots of fear over purported high cost of gold. There's a few

  "application" secrets but it is the ultimate surface finish.



  Now that the cat is out of the bag, how come you didn't mention immersion

  silver?





  Gerry Gagnon





  From: Lee parker <[log in to unmask]<mailto:[log in to unmask]>>

  Reply-To: TechNet E-Mail Forum <[log in to unmask]<mailto:[log in to unmask]>>,

Lee parker

  <[log in to unmask]<mailto:[log in to unmask]>>

  To: [log in to unmask]<mailto:[log in to unmask]>

  Subject: Re: [TN] best plated surface finish

  Date: Wed, 16 Nov 2005 08:25:34 -0500



  John



  Another option is flash gold over nickel. Both are plated inline using an

  electrolytic process(as opposed to ENIG). The gold thickness is roughly

two

  micro inches. The OEMs that I am familiar with that have used this finish

  have reported very good results.



  Most of the PCB suppliers providing this process are in China.



  Best regards



  Lee



  J. Lee Parker, Ph.D.

  JLP Consultants LLC

  804 779 3389

  ----- Original Message -----

     From: Babcock

John<mailto:[log in to unmask]<mailto:[log in to unmask]>>

     To:

[log in to unmask]<mailto:[log in to unmask]<mailto:[log in to unmask]<mailto:TechNet

@IPC.ORG>>

     Sent: Tuesday, November 15, 2005 7:28 PM

     Subject: [TN] best plated surface finish





     If somebody wants an extra smooth plating finish using lead free

plating

     what material would they use...and what would be the finishing process?

     I've heard HASL is sort of rough...and it really doesn't apply using

     silver solder because of the melting temps.

     Is ENIG (electroless nickel immersion gold) the way to go to get a

     smooth finish?



     thanks!



     John Babcock

     PCB Designer III

     Isothermal Systems Research (ISR)

     2218 N. Molter Rd

     Liberty Lake, WA 99019



[log in to unmask]<mailto:[log in to unmask]<mailto:jbabcock@sprayco

ol.com<mailto:[log in to unmask]>>

     P: (509) 241-4641

     F: (509) 444-1082



     This E-mail and any files transmitted with it are confidential and

     proprietary in nature and intended solely for the use of the individual

     to whom it is addressed.  If you have received this E-mail in error,

     please send it back to the person that sent it to you. Any views or

     opinions presented are solely those of its author and do not

necessarily

     represent those of Isothermal Systems Research, Inc.   Unauthorized

     publication, use, dissemination, forwarding, printing or copying of

this

     email and its associated attachments is strictly prohibited.  Thank you

     for your cooperation.





     ---------------------------------------------------

     Technet Mail List provided as a service by IPC using LISTSERV 1.8e

     To unsubscribe, send a message to



[log in to unmask]<mailto:[log in to unmask]<mailto:[log in to unmask]<mailto:LIST

[log in to unmask]>> with following text in

     the BODY (NOT the subject field): SIGNOFF Technet

     To temporarily halt or (re-start) delivery of Technet send e-mail to



[log in to unmask]<mailto:[log in to unmask]<mailto:[log in to unmask]<mailto:List

[log in to unmask]>>: SET Technet NOMAIL or (MAIL)

     To receive ONE mailing per day of all the posts: send e-mail to



[log in to unmask]<mailto:[log in to unmask]<mailto:[log in to unmask]<mailto:List

[log in to unmask]>>: SET Technet Digest

     Search the archives of previous posts at:



http://listserv.ipc.org/archives<http://listserv.ipc.org/archives<http://lis

tserv.ipc.org/archives<http://listserv.ipc.org/archives>>

     Please visit IPC web site



http://www.ipc.org/contentpage.asp?Pageid=4.3.16<http://www.ipc.org/contentp

age.asp?Pageid=4.3.16<http://www.ipc.org/contentpage.asp?Pageid=4.3.16<http:

//www.ipc.org/contentpage.asp?Pageid=4.3.16>>

  for additional information, or contact Keach Sasamori at



[log in to unmask]<mailto:[log in to unmask]<mailto:[log in to unmask]<mailto:sasako@ipc

.org>> or 847-615-7100 ext.2815

     -----------------------------------------------------



  ---------------------------------------------------

  Technet Mail List provided as a service by IPC using LISTSERV 1.8e

  To unsubscribe, send a message to

[log in to unmask]<mailto:[log in to unmask]> with following text in

  the BODY (NOT the subject field): SIGNOFF Technet

  To temporarily halt or (re-start) delivery of Technet send e-mail to

  [log in to unmask]<mailto:[log in to unmask]>: SET Technet NOMAIL or (MAIL)

  To receive ONE mailing per day of all the posts: send e-mail to

  [log in to unmask]<mailto:[log in to unmask]>: SET Technet Digest

  Search the archives of previous posts at:

http://listserv.ipc.org/archives<http://listserv.ipc.org/archives>

  Please visit IPC web site

http://www.ipc.org/contentpage.asp?Pageid=4.3.16<http://www.ipc.org/contentp

age.asp?Pageid=4.3.16>

  for additional information, or contact Keach Sasamori at

[log in to unmask]<mailto:[log in to unmask]> or

  847-615-7100 ext.2815

  -----------------------------------------------------



  _________________________________________________________________

  Express yourself instantly with MSN Messenger! Download today - it's FREE!



http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/<http://messe

nger.msn.click-url.com/go/onm00200471ave/direct/01/>



  ---------------------------------------------------

  Technet Mail List provided as a service by IPC using LISTSERV 1.8e

  To unsubscribe, send a message to

[log in to unmask]<mailto:[log in to unmask]> with following text in

  the BODY (NOT the subject field): SIGNOFF Technet

  To temporarily halt or (re-start) delivery of Technet send e-mail to

[log in to unmask]<mailto:[log in to unmask]>: SET Technet NOMAIL or (MAIL)

  To receive ONE mailing per day of all the posts: send e-mail to

[log in to unmask]<mailto:[log in to unmask]>: SET Technet Digest

  Search the archives of previous posts at:

http://listserv.ipc.org/archives<http://listserv.ipc.org/archives>

  Please visit IPC web site

http://www.ipc.org/contentpage.asp?Pageid=4.3.16<http://www.ipc.org/contentp

age.asp?Pageid=4.3.16> for additional information, or contact Keach Sasamori

at [log in to unmask]<mailto:[log in to unmask]> or 847-615-7100 ext.2815

  -----------------------------------------------------



---------------------------------------------------

Technet Mail List provided as a service by IPC using LISTSERV 1.8e To

unsubscribe, send a message to [log in to unmask] with following text in the

BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or

(re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet

NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send

e-mail to [log in to unmask]: SET Technet Digest Search the archives of

previous posts at: http://listserv.ipc.org/archives Please visit IPC web

site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional

information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100

ext.2815

-----------------------------------------------------



---------------------------------------------------

Technet Mail List provided as a service by IPC using LISTSERV 1.8e

To unsubscribe, send a message to [log in to unmask] with following text in

the BODY (NOT the subject field): SIGNOFF Technet

To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)

To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest

Search the archives of previous posts at: http://listserv.ipc.org/archives

Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815

-----------------------------------------------------



____________________________________________________________________________
_

Scanned by Sanmina-SCI eShield
____________________________________________________________________________
_



_____________________________________________________________________________

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
Scanned by Sanmina-SCI eShield  _____________________________________________________________________________

ATOM RSS1 RSS2