Sender: |
|
X-To: |
|
Date: |
Fri, 4 Nov 2005 11:33:40 +0200 |
Reply-To: |
|
Subject: |
|
From: |
|
Content-Transfer-Encoding: |
quoted-printable |
In-Reply-To: |
|
Content-Type: |
text/plain; charset=ISO-8859-1; format=flowed |
MIME-Version: |
1.0 |
Parts/Attachments: |
|
|
On request. Even 99% IPA has sufficient impure water in it to have a
finite conductivity. To make up the Contaminometer solutions in a past
life, I used pro analysi 99.9% reagent grade but I still had to deionise
it before mixing with water at <0.06 µS-cm (so-called 18 meg water), to
ensure minimal ionics before packing (note I didn't deionise the
mixture). Of course, the conductivity rose after packing, in PE
containers that had been soaked for 24 hours in similar solution, as the
solution will absorb CO2 like gangbusters.
The upshot is that IPA does contain unspecified ionic impurities which
will be deposited in small quantities after evaporation. The downshot is
that I believe these may be harmless in most circumstances with 99% IPA
or purer.
However, the unspecified contaminants that will be spread over the
assembly with an IPA wash MAY be sufficiently ionic to be dangerous. IPA
is NOT a good idea but, if it were to be used, it must be followed by a
DI water wash and rinse to ensure adequate removal of residual ionics,
especially when the history of the returned goods is unknown (they may
have been used near stormy seas or salted roads, for example). As you
have to wash, anyway, better just to wash with a suitable detergent and
forget IPA which is flammable (flash point ~12°C), volatile and toxic
(TWA OEL 400 ppm in many countries).
Brian dixit
Barbara J. Rich wrote:
>
>
> I am looking for any information on using compressed air to blow off
> "dust bunnies" on circuit boards coming from the field.
>
>
>
> Barb Rich
>
> Admin. Support Mfg.
>
> Sanmina-Sci
>
> 321 S. Taylor Ave.
>
> 303-264-2009
>
>
>
>
> _____________________________________________________________________________
> Scanned by Sanmina-SCI eShield ________________________________
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 1.8e
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
> _____________________________________________
>
--
______________________________________________
Please note new e-mail address [log in to unmask]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|