Michel,

I'll wait to comment until after I look at the picture once it is posted on Steve's web page but I couldn't tell from your description if there was a component on the pad and if so was it removed or was the pad that was examined a non-populated pad?

Regards,
George
George M. Wenger
Reliability / FMA Engineer
Base Station and Subsystems Group
Andrew Corporation, 40 Technology Drive, Warren, NJ 07059 (908) 546-4531 [log in to unmask]


-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Arbour, Michel
Sent: Wednesday, June 08, 2005 9:48 AM
To: [log in to unmask]
Subject: [TN] Solderability issues with ENIG finish


> Hi ,
> We've been having some solderability problems with one of our supplier. A
> populated PCB was sent for elementary analysis and we got the results back
> from the lab.
> Before going further in the corrective action process i would like to know
> if some of you agree and support the conclusions of the report based on
> the following data.
>
> - The board sent to analysis was populated , one half of a smt pad  did
> not wet with solder the other half wetted properly
> - The problem was noticeable on approx. 2% of the lot of PCB. 2-3 pads per
> board
> - The pad could not be soldered using an iron pen
> - Solder paste is standard Sn63, Pb37
>
> Two area on the pad were analyzed, one that was wetted , the other was
> not.
> Concentrations of element found  were the following
> - On the wetted area of the pad ALIAS : "AREA B"
> 5.40% C
> 2.04% N
> 0.81% O
> 45.32% Sn
> 2.45% Ni
> 3.67% Cu
> 40.31% Pb
>
> On the unsolderable area of the pad ALIAS "AREA A"
> 6.08% C
> 9.08% P
> 9.55% Sn
> 66.62% Ni
> 3.47% Cu
> 5.20% Au
>
> The conclusion of the report states :
> Area A is a fracture surface at the intermetallic boundary while Area B is
> a fracture surface at or near the bulk solder.  No mud cracking is seen at
> Area A which indicates that black nickel was most likely not present.  The
> fact that there is a fairly large gold peak at area A indicates that there
> may not have been sufficient time to adequately form the solder joint as
> the gold may not have had time to diffuse into the bulk solder.
>
> I can post a picture of the pad if you can point me to a location
>
>
> Michel Arbour
> Kontron Canada Inc.
>

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

------------------------------------------------------------------------------------------------
This message is for the designated recipient only and may
contain privileged, proprietary, or otherwise private information.  
If you have received it in error, please notify the sender
immediately and delete the original.  Any unauthorized use of
this email is prohibited.
------------------------------------------------------------------------------------------------
[mf2]

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------