TECHNET Archives

June 2005

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Kanaiyalal Patel <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Kanaiyalal Patel <[log in to unmask]>
Date:
Wed, 8 Jun 2005 07:06:56 -0700
Content-Type:
text/plain
Parts/Attachments:
text/plain (98 lines)
I was reading the guideline as it says that avoid
stubbing on board design hence my question. I was
thinking it is a via access to test or testpoint to
test near by pad but I am not sure.

Re,
Ken Patel

--- Dave Simonik <[log in to unmask]> wrote:

> Could this be referencing the plated hole wall
> remaining above the Must Not
> Cut (MNC) layer after Back Drilling on back planes?
> This is normally
> referred to as the 'Stub'.
>
> Dave Simonik
> Sanmina SCI
> Owego NY Division
>
> -----Original Message-----
> From: Kanaiyalal Patel
> [mailto:[log in to unmask]]
> Sent: Wednesday, June 08, 2005 9:54 AM
> To: [log in to unmask]
> Subject: stubbing in circuit design?
>
>
> All,
> What is stubbing in PCB circuit design? Can some one
> send me a picture or link to visulize it?
>
> Re,
> Ken Patel
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using
> LISTSERV 1.8e To
> unsubscribe, send a message to [log in to unmask] with
> following text in the
> BODY (NOT the subject field): SIGNOFF Technet To
> temporarily halt or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet
> NOMAIL or (MAIL) To receive ONE mailing per day of
> all the posts: send
> e-mail to [log in to unmask]: SET Technet Digest
> Search the archives of
> previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web
> site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
> additional
> information, or contact Keach Sasamori at
> [log in to unmask] or 847-615-7100
> ext.2815
>
-----------------------------------------------------
>
>
____________________________________________________________________________
> _
> Scanned by Sanmina-SCI eShield
>
____________________________________________________________________________
> _
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using
> LISTSERV 1.8e
> To unsubscribe, send a message to [log in to unmask]
> with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of
> Technet send e-mail to [log in to unmask]: SET Technet
> NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts:
> send e-mail to [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
> additional information, or contact Keach Sasamori at
> [log in to unmask] or 847-615-7100 ext.2815
>
-----------------------------------------------------
>

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2