Steve, thanks for posting the pictures,
According to the recipe and computer screen at the reflow, the peak
temperature is 240, the machine in use is a Electrovert Omniflo 7E
Profile is as follows
130 150 160 165 165 210 240 Rate is 35"/min
As far as contamination, the poor solder is not limited to one
particular component, also if I use a hand iron "correctly" then the
component does not pull off the pcb.
Thanks,
Jason
-----Original Message-----
From: [log in to unmask] [mailto:[log in to unmask]]
Sent: April 25, 2005 1:34 PM
To: TechNet E-Mail Forum; Jason Larson
Cc: [log in to unmask]
Subject: Re: [TN] Solder reflow
Hi Jason!
I got the pictures you sent to me posted up on my web page for everyone
to take a look at. Go to: http://www.stevezeva.homestead.com
and look at "Swiss Cheese Solder, and Swiss Cheese Solder 2".
What it looks like to me is that either the component had contamination
on the leads and didn't allow the solder to wet, or that the solder
wasn't liquidous long enough to form the metallurgical bond, or allow
all the voids to work themselves out of the joint...I see a lot of voids
in the solder.
Do you know what your peak temperature was during reflow, and how long
did it stay above liquidous?
Kind regards,
-Steve Gregory-
Senior Process Engineer
LaBarge Incorporated
Tulsa, Oklahoma
(918) 459-2285
(918) 459-2350 FAX
|---------+---------------------------->
| | Jason |
| | <jlarson@PACIFICI|
| | NSIGHT.COM> |
| | Sent by: TechNet |
| | <[log in to unmask]>|
| | |
| | |
| | 04/25/2005 02:38 |
| | PM |
| | Please respond to|
| | TechNet E-Mail |
| | Forum; Please |
| | respond to Jason |
| | |
|---------+---------------------------->
>-----------------------------------------------------------------------
---------------------------------------|
|
|
| To: [log in to unmask]
|
| cc:
|
| Subject: [TN] Solder reflow
|
>-----------------------------------------------------------------------
---------------------------------------|
Good day,
investigation into solder reflow performance reveals components that
pull out of the solder fillet with no damage to the component and the
fillet is left intact as well. Solder that was under the component looks
like swiss cheese with multiple holes. What part of the reflow is the
likely cause, conveyor speed, pre-heat, reflow heat, or cool down?
Thanks in advance for any help
Jason
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-615-7100 ext.2815
-----------------------------------------------------
__________________________________________________________________
This message may contain information that is privileged and confidential
to LaBarge, Inc. It is for use only by the individual or entity named
above. If you are not the intended recipient, you may not copy, use or
deliver this message to anyone. In such event, you should destroy the
message and kindly notify the sender by reply e-mail.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
