Is the board material FR-4 or something else?
Joe Johnson
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Barry Gallegos
Sent: Wednesday, April 20, 2005 12:52 PM
To: [log in to unmask]
Subject: Re: [TN] "Poor mans" custom board support...
Another thought would be a Carrier capable of going thru SMT and the
Wave Solder processes Where you do not remove the panel/array until
after Wave.
Barry.
-----Original Message-----
From: Colin McVean [mailto:[log in to unmask]]
Sent: Wednesday, April 20, 2005 10:32 AM
To: [log in to unmask]
Subject: Re: [TN] "Poor mans" custom board support...
We sometimes perform "V"-scoring on boards less than 0.031" (0.8mm)
thick down to 0.0010" (0.25mm) on a 16" x 12" panel. Albeit very flimsy,
it does hold together, but I suspect our customer is only hand soldering
thus there are no sagging issues invloved
Colin McVean
Production Manager
Artetch Circuits Limited
Tel: 01903 725365
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Valerie St.Cyr
Sent: 20 April 2005 17:27
To: [log in to unmask]
Subject: Re: [TN] "Poor mans" custom board support...
I'm not positive, but I think the "thinness" of the board at .031"
prohibits using
v-scoring; there would be very little residual material to hold the
boards
together in the assembly panel - they would probably snap apart just
picking them up .....
Valerie
Eric Bonatti <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
04/20/2005 10:51 AM
Please respond to TechNet E-Mail Forum; Please respond to Eric Bonatti
To: [log in to unmask]
cc:
Subject: Re: [TN] "Poor mans" custom board support...
Just curious, but would it not have been easier to v-score the pcbs in
the panel instead of router the edge and the mouse-bites?
Eric Bonatti, C.I.D.
PCB Designer
StrataFLEX Corporation
Tel.: +1.416.752.2224 xt.227
Fax: +1.416.752.6719
Toll Free: +1.866.771.7765
E-mail: [log in to unmask]
Web: www.strataflex.com
-----Original Message-----
From: Stephen Gregory [mailto:[log in to unmask]]
Sent: Tuesday, 19 April 2005 19:24 PM
To: [log in to unmask]
Subject: [TN] "Poor mans" custom board support...
Hi all!
I'm sure a lot of us have heard the saying; "Necessity is the Mother of
Invention", well I ran across a situation where it became necessary to
come up with something to solve a problem.
We have this assembly here that is in a vey fragile panel. The
individual board is only 1-inch wide, about 4.5-inches long,
.031 thick, and double-sided SMT that is fairly dense.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
