Thanks for all your help on this question.
It was very helpful.
Again happy holidays to all.
David Harman
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Frank Kimmey
Sent: Thursday, December 23, 2004 10:31 AM
To: [log in to unmask]
Subject: Re: [TN] Immersion gold specification
Well, now that Jeff has told you about the standard here is a little
more.
As Paul says, "it depends"
Though ENIG is a great finish for today's designs there are some
definite issues with the latest IPC standard.
Depending on the type of design you may want to modify the callout to
fit your requirements.
1. Use standard as a reference for digital designs (remind your
fabricator that "black pad" is not acceptable) 2. Reduce the nickel
thickness for RF designs as more nickel creates a bigger barrier for the
RF to flow.
Personally I callout 3 to 8 microinches of Immersion Gold over 50 to 150
microinches of Electroless Nickel.
But then I am doing high powered, low loss required RF.
Good Luck and have a Happy Holidays
Hope it helps,
FNK
Frank N Kimmey CID+
Principal PCB Designer
Powerwave Technologies Inc
Office 916-941-3159
Fax 916-941-3195
Cellular 916-804-2491
-----Original Message-----
From: Jeffrey Bush [mailto:[log in to unmask]]
Sent: Thursday, December 23, 2004 10:10 AM
To: [log in to unmask]
Subject: Re: [TN] Immersion gold specification
The current ENIG standard is IPC-4552. The spec on thickness for all
classes is 2 uinch minimum for gold and 118-236 for nickel.
Jeffrey Bush
Director, Quality Assurance and Technical Support
VERMONT CIRCUITS INCORPORATED
76 Technology Drive - POB 1890
Brattleboro, Vermont 05302
Voice: 802.257.4571.21 Fax: 802.257.0011
http://www.vtcircuits.com
-----Original Message-----
From: David Harman [mailto:[log in to unmask]]
Sent: Thursday, December 23, 2004 1:01 PM
To: [log in to unmask]
Subject: [TN] Immersion gold specification
Hope the network out here has a great holiday and successful new year.
I have one last question for this year regarding plating standards and
specifications.
I am trying to call out gold immersion specification over nickel on my
PCBA. My understanding is Mil-G-45204 type ll is no longer a valid
specification.
Is the industry standard 3 micro inches max - 1 micro inch min. (As
long as the process can be controlled you should not have any nickel
migration.) Is this correct.
Can some one tell me how I would spec this out on my drawing and what
standard is used in the industry for gold immersion over a an absolute
minimum of .00005 nickel.
Thanks
David Harman
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
