Sender: |
|
X-To: |
|
Date: |
Wed, 1 Dec 2004 13:24:09 -0600 |
Reply-To: |
|
Subject: |
|
MIME-Version: |
1.0 |
Content-Transfer-Encoding: |
quoted-printable |
Content-Type: |
text/plain; charset="us-ascii" |
From: |
|
Parts/Attachments: |
|
|
Kevin, this type of package is not required to have solderable surfaces
on the edges of the component--only on the bottom. The "bubble" of
solder on the edges is typical.
IPC-A-610D Clause 8.2.13 will have acceptance criteria for this kind of
package. You can download and review this draft at www.ipc.org/status
Jack
Jack Crawford, IOM
IPC Director Certification and Assembly Technology
[log in to unmask]
NEW PHONE 847-597-2893
NEW FAX 847-615-5693
IPC HAS MOVED- NEW ADDRESS:
3000 Lakeside Drive, Suite 309 S
Bannockburn, IL, 60015
New main Phone 847-615-7100
New main fax 847-615-7105
Check www.ipc.org/move for new staff phone numbers.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Kevin Jaworenko
Sent: Wednesday, December 01, 2004 8:44 AM
To: [log in to unmask]
Subject: [TN] Help, Help, I have a QFN Package I don't know what to do!
G'day Everyone.
Well as the subject states we are currently running a prototype
assembly with a new package style to me, a QFN (Quad Flat No-lead). I
had to look that one up myself.
The problem is when we were trying to reflow the part, the
solder joint looks very poor, with little to no solder seen on the edge
of the component lead and the pad on the PCB, or a bubble of solder seen
on end of the component between the edge of the component lead and the
pad of the PCB.
I'm currently setting up to X-ray the components to see if the
foot actually has a good solder joint underneath the component, where
the lead has been curled around the component, but has anyone else had
any dealings with this particular component type before and would be
willing to share?
I looked up the component manufacture's website and they show
that this component has a required peak temperature of 235 (+5/-0)
degrees C.
That seems like a lot of heat for a non lead-free component.
Feel free to email me offline if anyone likes.
Thanks in advance.
Kevin Jaworenko
Manufacturing Engineering Technologist
Vansco Electronics LP
(204) 453 - 3339 ext. 622
(204) 453 - 3663 FAX
[log in to unmask]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|