Subject: | |
From: | |
Reply To: | |
Date: | Tue, 23 Nov 2004 15:22:18 +0100 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Hi Steve & other Technetters,
From all the uncoated boards of this batch we have removed a component
to see which state the soldermask is in. 50% was very bad, the other 50%
has the problem just a little bit on the outer edges of the
solderresist. All of these are from one single datecode of bare boards,
other datecodes are perfect. That's why we expect that 50% of the coated
boards have the same issue.
A question that I have is how bad it actually is to have this quality
of soldermask (it has lost adherence and is flaking off) when the boards
are parylene coated. Any opinions on this?
Daan
B.T.W. I searched the Technet archives for "Dynamask" and all subjects
that I found were about flaking of soldermask. Nice mask this is!
>>> <[log in to unmask]> 11/22/04 11:59pm >>>
Hi Daan!
I'm sorry, I can't give you any ideas of how you'll be able to inspect
beneath the components reliably for the integrity of the soldermask.
I do have a couple of questions, how do you know it's only 50% of the
boards? To me, if you have that high of a percentage of boards that
have the issue,
I would be suspect of them all. Do you know what the cause is of the
mask
flaking?
I have had my soldermask issues, and all of them without question have
occured with dry films. I have had Dynachem (now Shipley) 5040 flake
from all the
copper surfaces. This was because it doesn't hold up well against the
Kyzen
Aquanox that we use to clean our assemblies. I've posted a couple of
times to
the Technet when this has happened to me.
What do you use to clean your assemblies with?
Sorry couldn't have of more help...
-Steve Gregory-
Hi Technet,
I have a problem with a batch of boards of which I know that an
estimated 50% of them have a problem with the soldermask. The mask
(Dynamask 5040 dry film) is flaking off the board, and we didn't
notice
this because the mask is only applied underneath the components (and
all
of them have a low standoff, which makes it impossible to inspect).
Now we need to know which of the boards are affected, but
desoldering
some of the parts to take a peek is not an attractive option as these
boards are already parylene coated.
I'm quite convinced that the answer is "no", but still I'd like to
give
it a try and ask the following question:
Does there exists ANY technology (non-destructive) that makes it
possible to inspect the quality of the soldermask underneath
components?
Best regards,
Daan Terstegge
PCB Assembly Department
Thales Land & Joint Systems
Tel +31(0)35 524 8297
Fax +31(0)35 524 8181
[log in to unmask]
Unclassified Email
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|