TECHNET Archives

October 2004

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
"Misner, Bruce" <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Misner, Bruce
Date:
Wed, 27 Oct 2004 08:31:50 -0600
Content-Type:
text/plain
Parts/Attachments:
text/plain (61 lines)
Ken,

If you just do an immersion Au (over Nickel), which by process, will give
you less than 10 u inches Au, embrittlement will not be an issue. If you
need the Au to Au wire bond to, 30 u inches Au will do it with out
embrittlement problems. Over 50 u inches of Au and you should start to be
concerned...will depend on the solder joint sizes. You want to stay under 3%
Au by volume (you can calculate it). As Jiri said, "the more Au the more
embrittlement" and it will manifest itself visually as grainy solder, the
more Au, the grainier.

An alternative could be to do a selective Au plate of the 2 pads...cost
issues.

Regards,
Bruce Misner

-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Bloomquist, Ken
Sent: Wednesday, October 27, 2004 9:53 AM
To: [log in to unmask]
Subject: [TN] Gold Board


Good morning TechNetters (at least here on the left coast),

We have a small assembly that requires a couple of pads to be gold plated.
We would like to gold plate the entire board but we're concerned about gold
embrittlement when we solder the components in. The board is completely
through hole and will be both wave soldered and hand soldered.

Do you think we have any concerns? Oh by the way this is a class 3 assembly.

Thanks,

KennyB

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2