Please find my resume attached as it applies to this position. I
have over 6 years experience as a Quality Control Manager in a military
environment. I have implemented and maintained the ISO 9002 program in
several positions. Statistical Process Control (SPC), FMEAs, CPKs and gauge
R& Rs are some of the tools I have used to maintain the ISO certification.
I have a chemistry education that I have applied in the 30 years that I
have been in the printed circuit board industry. I have supervised up to 15
people in a manufacturing environment to include electrical test, wet and
dry labs and final inspection. I work and interact well with suppliers,
regulatory agencies and customers. I have working knowledge of Mil-std-
2000, Mil-prf-31032, Mil-P-50884, IPC-A-600, IPC-A-610, IPC-TM-650, IPC-
6012 and IPC-6013. Please review my experience and education in
consideration for this position. You may contact me at your earliest
convenience.
Best Regards,
Judy Rae Brown
JUDY RAE BROWN
4525 Temescal Ave. Norco, California
951 735-8416 [log in to unmask] cell 909-772-8646
OBJECTIVE
A challenging position, which requires extensive quality control,
management, technical abilities, and provides opportunity for professional
growth and advancement.
Qualifications
· 30 years successful experience in Quality Assurance Management,
Laboratory, Inspection and Cross-Section Evaluation
· Analysis of Root Causes for Nonconforming Material
· Auditor of Quality systems for deficiencies and implementing
preventive and corrective action
· Working Member of I.P.C. Publications
· Retention and Re-qualifications (DESC)
· Writing Quality Control procedures and inspection plans
· Expertise Compliance Auditing ISO 9000; Corrective Action Logistics
· Proficient in Total Quality Management
· Process Engineering and plating
EXPERIENCE
May 2003 to January 2004 Multifineline Electronics-Anaheim,
Calif.
Quality Assurance Engineer-60K-left due to reorganization
Provided technical support to customer quality audit. Tools used
were FMEAs, PPAPs, CPKs, gage R & Rs, defect root cause analysis, process
anomalies and surveys. I was responsible for the material review board
disposition of in house non-conforming material based on customer
requirements. The disposition was based on next assembly risk assessment.
December 2002 to April 2003 Cosmotronic Corp.-Irvine, Calif.
Quality Assurance supervisor-52K-left due to Co.
bankruptcy
Supervised 12 people in the electrical test and inspection area for
the manufacture of rigid and rigid- flex printed circuit boards for
military use. Responsible for the returned material disposition of customer
returned non-conforming material and implementation of internal corrective
actions. Reorganized the electrical test department for optimal retrieval
of the test fixtures.
May 2000 to October 2002 Winonics, Inc.-Fullerton, Calif.
Quality Assurance Manager-52K-left due to facility closing
Chair the quarterly management review meeting, maintain the
internal Quality audit system to the ISO standard 9002, review, track and
investigate customer complaints, chart first pass yields for AOI,
electrical test and final inspection, maintain the return material
authorization system, assist quality supervisor, lead and inspection,
respond to customer requests for corrective action, maintain the
calibration system, UL registration book, inspection and test stamp control
books, issue monthly SQC report and maintain the internal corrective action
system, evaluate all customer returns and pull stock for similar
evaluation, maintain the auditor pool and update their training as
required. Gage R & R, SPC and CPK studies.
January 1997 to November 1999 Hughes Electronics Corporation- El
Segundo, Calif.
Member of Technical Staff (MTS-3)-50K-left due to massive lay
off
Responsibilities include performing all Quality functions relating to the
Manufacturing of Multi-layer Printed Wiring Boards/assemblies Tracking all
manufacturing metrics and working with Manufacturing to improve
production. Facilitator for various areas to resolve process issues and
problems. Strong ability to make decisions regarding acceptance or
rejection of hardware based on drawings and specification requirements.
Control point for the Contractor's Self-oversight System.
1995-1996 Cirtech- Orange, Calif.
Quality Assurance Manager-49K-temporary assignment
Worked all aspects of Quality Assurance. Performed audits of quality
procedures and military specification revisions. Requalified the GR and GI
material. Updated Quality manuals. Member of Material Review Board
(MRB). Performed planning inspection of all incoming orders.
February 1995-December 1995 Computer Education Institute-Riverside, Calif.
Student
Successfully completed Introduction to Computers/Windows, Microsoft
Word for windows, Excel, Office skill/database and computerized
accounting.
February 1993-March 1995 Pioneer Circuits- Santa Ana, Calif.
Quality Assurance Manager-49K
Responsibilities included overseeing and managing the Quality
Assurance Department. The SPC program was implemented for 6 key processes.
Interfaced with Customer on Quality issues and surveys. Trained inspectors
and ensured personnel were kept up to date with the Manufacturing
procedures. Maintained a complete calibration program in accordance with
Government requirements. Developed a return material authorization system,
responsible for in-house and Customer request for Corrective action.
1990-1992 Self-Employed
Trainer
Trained and raced performance horses for competition in rodeos.
January 1984-May 1990 Hughes Aircraft Ground Systems-
Fullerton, Calif.
Product Assurance Engineer
Processed all audits with government agencies (DCAS and DESC).
Implemented statistical process control of laminate testing, C and B stage
Epoxy and Polyimide. Approved work instructions and off-load source
surveillance of Printed Wiring Boards. Participated in the
performance/cost improvement program. Performed source surveillance
acceptance prior to shipment. Coordinated testing program for Norplex.
January 1970-January 1984 Singer Kearfott, San
Marcos, California
Materials and Process Engineer
Analyzed plating tanks, performed cross section analysis of printed
circuit boards. Monitored the conformal coating and wave solder machines.
Designed a new wet and dry laboratory.
Education
· Grossmont Jr. College 9/67 - 6/68 Pre-Med
· Palomar Jr. College 1/70 - 6/70 Pre-
Med
· San Diego State Univ. 9/66 - 6/69
Microbiology/Chemistry
· Computer Education Inst. 2/95 - 12/95
Computer
Academic training - Certificates
· Electrostatic Discharge Cert. 9/87
· Printed Circuit Technology 86/87
· Quality Assurance 1/87
· Professional Advanced Course in Technology Assessment of Laminates
· Continuous Measurable Improvement
· Statistical Thinking for Manufacturing Process Control
·
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
---------------------------------------------------------------------------------
|
