TECHNET Archives

June 2004

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Mike Fenner <[log in to unmask]>
Reply To:
Date:
Wed, 9 Jun 2004 08:59:39 +0100
Content-Type:
text/plain
Parts/Attachments:
text/plain (69 lines)
There is a possible similar problem with the use of fusible alloys used as
jigs, pipe bending etc. These do not leave the factory as part of the
product, but are recycled internally. So it is possible to conclude that
under the directives possession of lead is not going to be a crime. Putting
it on the market in electrical or electronic products is what will be
banned. So your position would appear to be analogous. The difference is
your possible generation of a waste stream and what you do with it. 
I have to stress that conclusions based on logical thinking after puzzling
the directives could be wrong. Logic and rational thinking are not always
the best guides in these matters. You might want to put this to the lead
free forum run by IPC. [It works just like TechNet.]

Regards 

Mike 


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Edward Szpruch
Sent: 09 June 2004 06:12
To: [log in to unmask]
Subject: [TN] Lead Free Issues


Hi,
I have to discuss from time to time the extend of Lead-Free directives and
policies.
As far as I understand Lead Free directives are dealing with populated PCB
only and have nothing with manufacturing of PCB , for example - using of
electroplated Pb/Sn as etch resist for pattern plating is not a issue as
long as Pb/Sn is stripped from the board and no Pb is present on the board .
In this respect removing of Pb/Sn electroplating facilities is not
requested.
Responds???
Edward

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
-----------------------------------------------------


:::::::::::::::::::::::::::

This email, its content and any files transmitted with it are intended solely for the addressee(s) and may be legally privileged and/or confidential. If you are not the intended recipient please delete and contact the sender by return and delete the material from any computer. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited.

Messages sent via this medium may be subject to delays, non-delivery and unauthorized alteration. This email has been prepared using information believed by the author to be reliable and accurate, but Indium Corporation makes no warranty as to accuracy or completeness. In particular, Indium Corporation does not accept responsibility for changes made to this email after it was sent. Any opinions or recommendations expressed herein are solely those of the author. They may be subject to change without notice.

:::::::::::::::::::::::::::

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------

ATOM RSS1 RSS2