Subject: | |
From: | |
Reply To: | TechNet E-Mail Forum. |
Date: | Wed, 30 Jun 2004 11:55:17 -0400 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Franklin -
It is obvious that you never did any ink on mylar drafting. The #4 grey
is not a rubber eraser, its a grinding stick. I have use them to hone
knife edges, and polish burrs off of parts in past lives ;-D
Jeffrey A McGlaughlin, CID
Engineering Designer
Battelle Memorial Institute
Columbus Ohio
http://www.battelle.org
[log in to unmask]
-----Original Message-----
From: Franklin [mailto:[log in to unmask]]
Sent: Wednesday, June 30, 2004 11:49 AM
To: [log in to unmask]
Subject: Re: [TN] Soldermask on PTH pad???
I can see a dremel sanding cone being used...but not an eraser...
Franklin
----- Original Message -----
From: "Mike Sewell" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Wednesday, June 30, 2004 10:22 AM
Subject: Re: [TN] Soldermask on PTH pad???
> We did something similar...had a stencil vendor cut aperatures for the
> features we wanted to remove then used a Dremel with the abrasive
> rubber tips. Something about putting RF flags on traces for tuning
> the assembly. Slow but it worked.
>
> Regards,
> Mike Sewell
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
> unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
> or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-509-9700 ext.5315
> -----------------------------------------------------
>
>
>
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
|
|