TECHNET Archives

March 2004

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Condense Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Content-Type:
text/plain; charset="iso-8859-1"
Sender:
Subject:
From:
"Tempea, Ioan" <[log in to unmask]>
Date:
Thu, 11 Mar 2004 19:57:54 -0500
MIME-Version:
1.0
X-To:
Reply-To:
"TechNet E-Mail Forum." <[log in to unmask]>, "Tempea, Ioan" <[log in to unmask]>
Parts/Attachments:
text/plain (103 lines)
Thanks for the valuable input.

Please note that the last thing I want is to give microVIP a bad name.
Therefore I have to clarify that my original questions apply to 0.010" vias,
mainly on 0.050"x0.040" pads.

Best regards,
Ioan

-----Original Message-----
From: Macko, Joe @ IEC
To: [log in to unmask]
Sent: 3/11/2004 6:51 PM
Subject: Re: [TN] Reliability of via in pad

Gary,

Good points.  Can you refer me to any studies that associate VIP design
vs.
"unacceptable"  voiding?  A little voiding may be good for reliability
but
too much is not good.  I struggle with determining how large or deep a
VIP
can be before it contributes or causes unacceptable voiding.

joe

-----Original Message-----
From: Gary Ferrari [mailto:[log in to unmask]]
Sent: Thursday, March 11, 2004 2:20 PM
To: [log in to unmask]
Subject: Re: [TN] Reliability of via in pad


Technetters,

Please let us not throw the baby out with the bath water. I would hate
for
VIP technology to get a bad name when in essence your valid concerns are
associated with larger vias than used in HDI technology. A similar panic
was
created
against dry film soldermasks because the commonly used dry film mask
thicknesses were around 0.006 in. When mask manufacturers introduced
high
conformance
thin masks (0.001 - 0.002 in) to address the needs of SMT , everyone
shunned
them because they were "dry film", when in reality their gripes were
with
the
thicker cousins.

Regards,

Gary

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text

in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or
847-509-9700 ext.5315
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
ext.5315
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------

ATOM RSS1 RSS2