Hi Steve,
  This web site may have the conversion you are looking for..
http://www.chemie.fu-berlin.de/chemistry/general/units_en.html

Regards,
Yasmeen

-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Steve Gregory
Sent: Thursday, February 26, 2004 12:36 PM
To: [log in to unmask]
Subject: [TN] Conductivity and Resistivity Correlation


Hi All!

Is there any chart, formula, or conversion that I can use to correlate a
conductivity reading to a resistivity reading?

The reason I'm asking is that I have a new batch cleaner that has been up
and
running the last three weeks or so. One of the neat things with the cleaner
is that during the rinse cycle, it monitors the rinse water resistivity to a
setting that you program in the machine. If it reaches that pre-programmed
resistivity setpoint before completing the number of rinse cycles that you
program,
it will terminate the rinse cycles and go into the dry cycle. If it never
reaches the resistivity setpoint within the number of rinse cycles that
you've
programmed, it will display "FAILED" on the touch screen. You can then run
another cycle, or start trying to figure out why the boards didn't come
clean.

Well, everything has been going fine with the cleaner up until yesterday.
Every batch of boards I ran failed the resistivity setting I had in the
machine.

The manual recommends a setting between 350-750 kohms, I've had my setting
at
550 kohms from the beginning, and everything has been fine. I've had to
lower
the setting to 400 kohms so the batches would pass. It's still within the
350-750 kohm range, but I'm curious why all of a sudden things won't pass at
550
kohm like it's been doing the few weeks.

So I called tech support for the cleaner, and they feel that my input DI
water may be going bad. I have a US Filters reverse osmosis filtering system
that
dumps that water into Ion exchange columns and that water goes directly to
my
cleaner. The DI system displays the conductivity of the output water in µS
(micro-siemins). I want to correlate that to resistivity to see if my DI
water is
truly going bad.

Thanks!

-Steve Gregory-

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------