TECHNET Archives

January 2004

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Dave Simonik <[log in to unmask]>
Reply To:
TechNet E-Mail Forum.
Date:
Wed, 28 Jan 2004 07:45:01 -0500
Content-Type:
text/plain
Parts/Attachments:
text/plain (92 lines)
David;

  Most any drill machine with depth control (Z axis micrometer scale) can be
used for this type of rework. Even a drill machine without depth control can
be used, by properly setting the down limit. I have done rework of this
nature in the past. However, there are a few things that must be considered.
First, are there components on both sides of the board? If there are
components on the bottom side of the board - opposite side of the board that
needs drilling, then a special fixture may need to be fabbed in order to
support the board on the drill table. (To prevent the board from 'rocking'
around, and to prevent damage to the components)  Next, if there are
components that are very close to the drill location, these components may
need to be removed. The reason for this is to allow enough room for the
pressure foot of the spindle. If the pressure foot of the spindle contacts
the components during the actual drill cycle, then the depth control will
not be accurate, and may even crush the components.

  A Uv laser can also be employed to rework these boards. Using a laser will
negate the pressure foot clearance requirements, but may still need a
fixture to hold and support the board. Most lasers do have limitations as to
how far the z axis can be operated, so if the components are very tall, plus
the height of the fixture, may violate the z axis height limitations. Using
a laser to do this will be difficult, and the rework house may need to cross
section a few boards in order to be sure the laser parameters are drilling
to proper depth. I have attempted through holes with a laser through very
thick panels, and have found that beyond .050" depth, the laser beam is now
out of focus, and no matter how many repetitions are applied, the beam has
'diverged' to the point where the centroidal energy of a Gaussian beam has
completely dissipated, and all the beam is doing at that depth is heating up
the laminate.

Dave Simonik
Laser Process Tech.
Sanmina SCI Corp.
Owego NY Division

-----Original Message-----
From: David Tremmel [mailto:[log in to unmask]]
Sent: Monday, January 26, 2004 6:00 PM
To: [log in to unmask]
Subject: Board rework


Hello everyone,

There are some populated boards which have an inner trace which needs to be
opened.

I need information on either leasing or purchasing the machinery or a
company (in North America or Mexico) that can drill thru an inner trace
which needs to be opened, but not entirely through the board.

Each boards needs 2 drillings.  I have approx. 15,000 boards.

Thank you in advance for the help.

Thank you,

David Tremmel
Belmont Trading Company
3160 MacArthur Boulevard
Northbrook, Il 60062
(847) 412-9690 - Ext. 346
(847) 858-5540 - Cell

_________________________________________________________________
Let the new MSN Premium Internet Software make the most of your high-speed
experience. http://join.msn.com/?pgmarket=en-us&page=byoa/prem&ST=1

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in the
BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet
NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send
e-mail to [log in to unmask]: SET Technet Digest Search the archives of
previous posts at: http://listserv.ipc.org/archives Please visit IPC web
site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
ext.5315
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------

ATOM RSS1 RSS2