The first thing to try is to bond to an unassembled, as received, board.
a) If that works, then you know that the problem lies with the
subsequent process. b) If not, the boards are unsuitable for bonding or
have been inappropriately stored.
If a) then one or both of the following may help:
a1) 35 - 40 µ" Au is next to bugger-all and is certainly porous. The Ni
underneath is probably oxidising and, as the oxide occupies more volume
than the metal, it is exuding to the surface. This can be proven by
trying to immerse a piece in 10% hydrochloric acid solution for 10
minutes at room temperature. Then rinse copiously in very pure DI water
(>5 Mohm-cm) and dry with a cold nitrogen blast. If that sample bonds
OK, you have your answer. This treatment may discolour the solder
joints, but will cause no harm to them (for your first trial, you can
try it on an unmounted board.
a2) your subsequent processes (pressing, soldering etc.) have
contaminated the surface, which is quite possible. The most likely
candidates are sublimated flux, contact materials during pressing or
residues from the cleaning (if any) process after soldering. It is not
possible to categorically recommend any cleaning process without knowing
a lot more about all your processes. However, I suggest you narrow it
down by trying to bond after each step of each process, in order, until
the bonding fails. The previous process then becomes the responsible one
and the cleaning process should become evident.
If b) then one or both of the following may be considered:
b1) if the boards are fresh, then take it up with your supplier to
correct the problem
b2) store the boards in nitrogen under slight pressure to prevent
oxidation (do not vacuum-seal, as this can draw contaminants out which
can settle on the bonding pads).
Hope this helps
Brian
Steve Kelly wrote:
> Fellow Technetters,
>
>
>
> I need some recommendations on how to clean wire bondable gold pads before
> bonding. We are electroplating 35-40 microinches of soft gold over 130
> microinches of nickel. After gold plating we have to go through 2 press
> cycles at 350 F for approx. 1.5 hours each to attach stiffeners onto the
> flex. We then surface mount components and reflow. After all these heat
> cycles we see some oxidation on the gold pads. What is a recommended
> cleaning process to have a "fresh" surface to wire bond to. Thanks for the
> help.
>
>
>
> Regards Steve Kelly
>
>
>
> PFC Flexible Circuits Limited
>
> Ph: (416) 750-8433
>
> Fax: (416) 750-0016
>
> Cell: (416) 577-8433
>
> E-Mail: [log in to unmask]
>
>
>
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 1.8e
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
> -----------------------------------------------------
>
>
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
