Subject: | |
From: | |
Reply To: | TechNet E-Mail Forum. |
Date: | Mon, 15 Dec 2003 15:41:54 -0700 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Chris,
Are you saying that if I have a .150 hole in a PCB I should expect a
tolerance for location to be about a dia. of .015 (MMC)?
Tom Burek
Ametek/Dixson
Chris Robertson <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
12/15/03 02:00 PM
Please respond to Chris Robertson
To: [log in to unmask]
cc:
Subject: Re: [TN] Hole tolerance
Doesn't quite work like that. It is dependant upon the manufacturer and
the
drill size. On average it is about 10% of the drill size rounded with a
minimum tolerance.
Conventional (everyone)
.010" - .003"
.030" - .004"
.050" - .005"
Advanced (roughly 9%, min .002")
.010" - .002"
.040" - .003"
.050" - .004"
You will find variations and some that can do even better, but this is my
rule of thumb.
It is a percentage, similar to the aspect ratio of board thickness to
minimum drill size.
(not a guru though)
Chris Robertson
Author "PCB Designer's Reference"
[log in to unmask]
ISBN: 0130674818
Search for it at www.amazon.com
----- Original Message -----
From: Tom Burek
To: [log in to unmask]
Sent: Monday, December 15, 2003 2:36 PM
Subject: [TN] Hole tolerance
Greetings guru's,
I have an inquiry into hole location tolerance, especially directed to
our
many PCB manufacturers listening in.
What is the best reasonable tolerance you can expect, world wide,
(overseas as well as domestic suppliers), for positional location of
plated and unplated holes, without adding addition cost to the circuit
board?
Expressed in a true position format, would a diameter of 3 mils. be
unreasonable? dia. .005?
Assume a moderate volume of production.
Thank you in advance.
Tom Burek
Ametek/Dixson
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-509-9700 ext.5315
-----------------------------------------------------
[log in to unmask]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-509-9700 ext.5315
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
|
|