Linda:
        Besides the professionally made gauges which are the better choice,
any machine shop can make gauges of about 1.5" square,  60 mills thick
aluminum pieces.  Cut out notches on each side of different heights, leaving
the ends of each side to slide over the board and the notched part be the
fixed gauge.  This tool will provide you with four gauges in one. They can
machine notch 10 or more at a time. Edges must be smoothen out to not
scratch boards. Stamp each side for its height and give them to the
operators.
        Regards,
        Ramon                             ----               ---

                                                   |   |________}  |

                                                   |_                _ |

                                                     |      0.060  |

                                                     |                |
                                                  _ |     0.030   |_
                                                  |    ________   |
                                                  ]__]            ]__}



> -----Original Message-----
> From: Linda Langley [mailto:[log in to unmask]]
> Sent: Wednesday, October 29, 2003 9:43 AM
> To: [log in to unmask]
> Subject: [TN] measuring tool
>
>
> Technetters,
>
> What type of measuring device do you use to check proper lead length? We
> need something to measure .030 on production line. We are currently using
> 6
> inch. Metal ruler but need something a little more accurate.
>
> Thanks for any suggestions.
>
> Linda
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
> unsubscribe, send a message to [log in to unmask] with following text in the
> BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET
> Technet
> NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send
> e-mail to [log in to unmask]: SET Technet Digest Search the archives of
> previous posts at: http://listserv.ipc.org/archives Please visit IPC web
> site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
> information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
> ext.5315
> -----------------------------------------------------
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 1.8e
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for additional information, or contact Keach Sasamori at [log in to unmask] or
> 847-509-9700 ext.5315
> -----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------