Steve,
We have an Electrovert Vectra system with an Ecno-fluxer that is actually a
USI unit.
I've found that for thicker back planes, I turn on my chip wave along with
the lambda wave. It really seemed to facilitate top side wetting. I also
spray the flux on pretty heavy as well, it seems to get the flux to wick up
the lead. I can recall thinking that I wasn't getting good topside due to a
lack of heat. The more heat I applied the worst it got. It was my belief
that the flux was drying out before the wave. So, I applied the flux a bit
heavier and turned down the pre-heat but turned on the chip wave. The
results were sweet.
Good luck.
Bill Kasprzak
Moog Inc. Manufacturing Engineering, Electronics
> -----Original Message-----
> From: Steve Gregory [SMTP:[log in to unmask]]
> Sent: Monday, April 07, 2003 10:36 PM
> To: [log in to unmask]
> Subject: Re: [TN] Wave soldering - Spray fluxer parameters
>
> Hi Peter!
>
> Not knowing what type of spray-fluxer you have, I'll tell you what I do
> here with the Opti-flux system I have...it's a ultra-sonic fluxer.
>
> What I look for is coverage first of all. That's easily checked by either
> using a piece of cardboard, or with kraft paper taped to the fixture
> you're using, that corresponds to the width of the conveyer. Then just run
> it through the fluxer with the heaters off. Take a look at the spray
> pattern and look for even coverage.
>
> With my spray fluxer I can adjust what's called the traverse speed, which
> controls how fast the spray head passes back and forth. If I run the main
> conveyor speed a little fast, I may need to increase the spray fluxer
> traverse speed so that there's even coverage...it's always worked for me.
>
> That being said, I'm running into a challenge with a big, thick (.125"),
> heavy back-plane that I'm trying to wave. It's a class-3 assembly, and
> having a hard time getting good top-side fillets. Gonna try pre-heating
> the assembly in a oven, taking it out and getting it into the wave before
> it has a chance to cool down a whole lot. I've tried playing with
> pre-heat, conveyer speed, etc...but it seems everything that I try to do
> on the wave, seems to dry-out, or kill the flux...
>
> Maybe someone has another suggestion...BTW, I have an Electrovert Electra.
>
> -Steve Gregory-
>
>
>
> Technet,
>
> Can anyone recommend a process for setting up the operating
> parameters
> for the spray fluxer?
>
> How can one verify the optimum amount of flux is being applied to
> the
> pcb prior to the board going through solder wave?
>
>
> Rgds,
> Peter
>
>
>
>
>
> -Steve Gregory-
> ---------------------------------------------------
> Technet Mail List provided as a free service by IPC using LISTSERV 1.8e
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
> information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
> ext.5315
> -----------------------------------------------------
>
---------------------------------------------------
Technet Mail List provided as a free service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
