Sender: |
|
X-To: |
|
Date: |
Fri, 14 Feb 2003 17:08:46 -0600 |
Reply-To: |
|
Content-type: |
text/plain; charset=iso-8859-1 |
Subject: |
|
MIME-Version: |
1.0 |
Content-transfer-encoding: |
quoted-printable |
From: |
|
Parts/Attachments: |
|
|
Hi Yannick! Take a look at JSTD-001B specification in the section 9 tables
- if the IC leads are exposed/nonplated due to shearing then you will not
get any wetting (nonwetting due to component design). You would need a very
aggressive flux chemistry to get wetting in these regions due to the
exposure the sheared edge metallization has undergone. Take a look at your
heel fillets - if they meet the 001/610 specification requirements then the
solder joint quality is good. Good Luck.
Dave Hillman
Rockwell Collins
[log in to unmask]
Yannick Brisson
<[log in to unmask]> To: [log in to unmask]
Sent by: TechNet cc:
<[log in to unmask]> Subject: [TN] Copper on lead
02/12/2003 04:18
PM
Please respond to
"TechNet E-Mail
Forum."; Please
respond to
Yannick Brisson
Hello,
I'm wondering if someone had issue with copper on IC lead. We had a
batch
of IC where we find that on the side of the lead and at the front about 1/4
of the lead that have copper. It's seem that the lead have been cut and
didn't get plated. What do you think we shuold do to get a good solder
joint. Because right now the solder stop where the copper begin. We use a
no-clean paste. Should we go to a more aggressive paste? like water
solube?
shuold we change our profile?, we get a peak of 220celcius.
Or anything else you have try?
Thanks You
Yannick Brisson
============================
Technicien SMT
Technician SMT
M2S Électronique
2855, Rue de Celles
Québec, Québec
G2C 1K7
Téléphone: (418) 842-1312 Ext: 264
Télécopie: (418) 842-0123
[log in to unmask]
============================
---------------------------------------------------
Technet Mail List provided as a free service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
ext.5315
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a free service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
|
|