I guess that's better than a life of wretching, Rick.
Good luck with them doegies.
Ron Dieselberg
-----Original Message-----
From: Howieson, Rick [mailto:[log in to unmask]]
Sent: Wednesday, August 09, 2000 17:28
To: [log in to unmask]
Subject: Re: [TN] Copper
Thanks to all for the info. And a special thanks to all TechNetters for
past expertise. I'm sorry to say I'm leaving the industry, effective
8.11.00 for the life of ranching.
I have really enjoyed this forum!!!
Thanks again,
Rick Howieson
General Technology Corp.
>-----Original Message-----
>From: Franklin D Asbell [SMTP:[log in to unmask]]
>Sent: Wednesday, August 09, 2000 3:02 PM
>To: [log in to unmask]
>Subject: Re: [TN] Copper
>
>Michael,
>
>I'm curious ~grinning~, in reading your disclaimer, it states I cannot
>read the e-mail, so in reading the disclaimer which is in part, the
>e-mail, am I in violation of anything ~grin~
>
>
>Just curious is all...
>
>
>Franklin
>
>
>
>
>"Carano,Michael" wrote:
>>
>> "NOTE: The information in this e-mail is confidential and may be legally
>>privileged. If you are not the intended recipient please notify the sender
>>immediately and then delete this e-mail. You must not read, copy, use or
>>disseminate this e-mail or any information in it . Although this e-mail
>>and any attachments are believed to be free of any virus or other defects
>>which might affect any computer or IT system into which they are received,
>>no responsibility is accepted by Laporte plc or any of its associated
>>companies for any loss or damage arising in any way from the receipt or
use
>>thereof. Any opinions expressed in this e-mail or any attachments are
those
>>of the individual sender and not necessarily the Company."
>> "
>>
>> Rick,
>>
>> These seem to be in the normal range for ductile copper. Typically, the
>> higher the elongation is, the lower the tensile strength, and vice-versa.
>> A problem would be in the elongation is say 33%, the tensile strength may
>> drop below 30,000 psi. While the deposit will not exhibit corner
cracking,
>> barrel cracking may be evident.
>>
>> Best regards,
>>
>> Mike Carano
>>
>> -----Original Message-----
>> From: Howieson, Rick [SMTP:[log in to unmask]]
>> Sent: Wednesday, August 09, 2000 3:04 PM
>> To: [log in to unmask]
>> Subject: [TN] Copper
>>
>> We run copper plating tests monthly and send these to an
>>independent
>> lab
>> for testing. The requirements are Tensile Strength 36,000 psi
>> minimum
>> and Elongation 6% minimum. My question to the experts is-- what
if
>> our
>> readings were high, i.e. 43,000 psi and 20% elongation?
>> TIA,
>> Rick Howieson
>> General Technology Corp.
>>
>> ##############################################################
>> TechNet Mail List provided as a free service by IPC using
LISTSERV
>> 1.8c
>> ##############################################################
>> To subscribe/unsubscribe, send a message to [log in to unmask] with
>> following text in
>> the body:
>> To subscribe: SUBSCRIBE TECHNET <your full name>
>> To unsubscribe: SIGNOFF TECHNET
>> ##############################################################
>> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
>> additional
>> information.
>> If you need assistance - contact Keach Sasamori at [log in to unmask]
>>or
>> 847-509-9700 ext.5315
>> ##############################################################
>>
>> ##############################################################
>> TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
>> ##############################################################
>> To subscribe/unsubscribe, send a message to [log in to unmask] with
following
>>text in
>> the body:
>> To subscribe: SUBSCRIBE TECHNET <your full name>
>> To unsubscribe: SIGNOFF TECHNET
>> ##############################################################
>> Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
>>additional
>> information.
>> If you need assistance - contact Keach Sasamori at [log in to unmask] or
>> 847-509-9700 ext.5315
>> ##############################################################
>
>##############################################################
>TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
>##############################################################
>To subscribe/unsubscribe, send a message to [log in to unmask] with following
>text in
>the body:
>To subscribe: SUBSCRIBE TECHNET <your full name>
>To unsubscribe: SIGNOFF TECHNET
>##############################################################
>Please visit IPC web site (http://www.ipc.org/html/forum.htm) for
additional
>information.
>If you need assistance - contact Keach Sasamori at [log in to unmask] or
>847-509-9700 ext.5315
>##############################################################
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following
text in
the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
If you need assistance - contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
##############################################################
##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in
the body:
To subscribe: SUBSCRIBE TECHNET <your full name>
To unsubscribe: SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional
information.
If you need assistance - contact Keach Sasamori at [log in to unmask] or
847-509-9700 ext.5315
##############################################################
|
