 
| Subject: | |
| From: | |
| Date: | Fri, 6 Jun 1997 10:14:06 -0500 |
| Content-Type: | text/plain |
| Parts/Attachments: |
|
|
The parts are already on the bottom side of the PCB
I am trying to design the stencil. There are other parts on the top side that
will be reflowed along with this part.__ _
----------\ \
_________________ | solder\ __________
PC Board | | Part | |PC Board
________________| |_______| |_________
-----------------------------------
Metal Plate
______________________________ Reply Separator _________________________________
Subject: Re: double sided reflow-soldering top side to bottom side
Author: "Jeffery L. Hempton" <[log in to unmask]> at INTERNET
Date: 6/6/97 9:51 AM
Aric,
I am trying to visualize what you are describing, and I come up a little
short. Could you be more specific, i.e., are there already parts on the top
or bottom side?? Sounds like you already have a stencil fabbed? I think we
can give you some creative ideas to help your problem if you clarify. Thanx.
At 08:52 AM 6/6/97 -0500, you wrote:
>
> I have an application where I need to reflow solder a part on the top
> side of a double sided SMD board through the board to a bottom side
> component without plating the hole.
>
> This part is large and is placed within a slot in the panel. It must
> physically touch the part on the bottom side.
>
> Does anyone have any suggestions on screen printing this,
>
> The stencil aperture will not contact the PCB surface where I need to
> put the paste, but will be over a slot in the PCB.
>
>
> Thanks for any help,
>
>
>
> Aric
>
>
>***************************************************************************
>* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
>***************************************************************************
>* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
>* with <subject: subscribe/unsubscribe> and no text in the body. *
>***************************************************************************
>* If you are having a problem with the IPC TechNet forum please contact *
>* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
>***************************************************************************
>
>
>
----------------------------------
Jeff L. Hempton phone: (219) 429-7335 Fax: (219) 429-4688
Boardshop Manufacturing Engineer Mail Stop: 25-31
Hughes Defense Communications
1010 Production Road, Fort Wayne, IN 46808-4106
Email: [log in to unmask]
"The man who rolls up his sleeves seldom loses his shirt."--Thomas Cowan
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To subscribe/unsubscribe send a message <to: [log in to unmask]> *
* with <subject: subscribe/unsubscribe> and no text in the body. *
***************************************************************************
* If you are having a problem with the IPC TechNet forum please contact *
* Dmitriy Sklyar at 847-509-9700 ext. 311 or email at [log in to unmask] *
***************************************************************************
|
|
|
