TECHNET Archives

September 1997

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Jeff Seeger <jseeger*remove_to_reply*@APPLIEDCAD.COM>
Reply To:
TechNet Mail Forum.
Date:
Tue, 23 Sep 1997 12:21:36 -0400
Content-Type:
text/plain
Parts/Attachments:
text/plain (111 lines)
Eddie Brunker wrote:
> <snip>
> Press Fit connectors can be mechanically inserted without soldering
> therefore the via can be connected to the plane along its full circumference
> with no thermal relief (a solid contact). This solid contact in turn gives
> lower inductance for power pins on a backplane.(Which is what the designers
> want).
> I get the impression that Press Fit is used not just by Compact PCI
> protocall (in our case 6U card computers) but anyone heading at high bus
> speeds in a backplane.

        Very true.  We have seen press-fit connectors in use in a number
        of large scale systems.

> connectors to address this is seriously worrying. Why should the Design
> fraternity dictate the assembly technique and not the end result required.

        We (the Design community) need to be involved in assembly methods
        selection.  Otherwise we have no way to anticipate or provide for
        the manufacturing communities' collective needs.

> In other words if they want reduced inductance why don't they just specify
> no thermal relief and let the assembly heads worry about the means of
> connection and whether soldering will be a problem.

        IPC's spec (D-275) is pretty clear on what's allowable for thermal
        connections in a wave-soldered environment.  There are increasing
        cases where wave is not possible, and press fit allows another
        method for mass termination of dense connections.  While it is a
        secondary operation, it is less burdensome than selective wave
        or fountain solder, at least with what I've seen and been told.

> APPLYING A FEW TONS OF PRESSURE TO AN ASSEMBLY to attach a connector seems
> to me to be primitive method.

        Like a blistering thermal excursion, or contact with a substance
        at much higher than Tg, what appears as brutality actually will
        work quite well with a little finesse added into the mix.  A pwb
        structured for press-fit will have a very well defined construction
        in the plated through hole, such that the compliant pin makes con-
        trolled contact with the barrel in soft metal.

> Does anyone out there use solid connection to vias on copper planes for the
> wave soldering process?  Has anybody done any trials on this?

        Not allowed per IPC specs.  This comes from a concensus of many
        assembly heads that tried to get good yields, my guess.

> It would be nice to see the design people told that there should be a STOP
> TO THIS BARBARIAN ASSEMBLY TECHNIQUE. It would be nice to see the connector
> manufacturers make connectors which provide shielding and conform to Compact
> PCI format and IEC1076 (or high speed bus formats) in Plated Through Hole OR
> Surface Mount packages.
> Pressumably SURFACE MOUNT WOULD HAVE NO THERMAL RELIEF DEMANDS as modern
> Convection ovens have no problems dealing with solid contacts to vias. So
> why not develop the Surface Mount version of the connector?

        Surface mount also offers very little mechanical support for large
        connectors or repeated insertions by field service folks with ham-
        mers.

Larry Campbell wrote:
>>
>> By no means should you press fit a connector or pin of any sort
>> into a platted thru hole that has intermal layer thermal layers, or
>> internal pads for that matter.  By pressing the pin into the hole
>> you run the risk of breaking the continuity of the PTH and not
>> make a connection to the internal layers, or possibly making
>> only intermittent connections internally.

        I have to disagree with Larry, but will grant the caveat that
        design, fabrication, and assembly resources all need the basic
        understanding to plan for this assembly method.  It's tried, it's
        true, and it saves a thermal excursion or other torturous method
        for high-density and/or large connectors and backplanes.  I'd
        venture to guess that most of the telephone traffic today travels
        through systems put together this way, as well as most cabinet
        style computers.

        Are there any real alternatives?  Is the assembly community ready
        for intrusive reflow of 800 pin connectors on 2mm spacing?  How
        about wave solder on a .250" thick board with 30 layers?  Press
        fit components and methods, deployed properly, enable a finer
        geometry on a larger scale than thru-solder methods, and offer
        more mechanical strength.

        Let's see:  Electrically better, higher density, more robust, no
        thermal cycle, accessible for In-Circuit-Test, all at the cost of
        slightly better than vanilla PTH tolerancing.  Sign me up!

        My two cents' worth.

        Regards to all,
--

      Jeff Seeger                             Applied CAD Knowledge Inc
      Chief Technical Officer                      Tyngsboro, MA  01879
      jseeger "at" appliedcad "dot" com                    978 649 9800

##############################################################
TechNet Mail List provided as a free service by IPC using LISTSERV 1.8c
##############################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe:   SUBSCRIBE TECHNET <your full name>
To unsubscribe:   SIGNOFF TECHNET
##############################################################
Please visit IPC web site (http://www.ipc.org/html/forum.htm) for additional information.
For the technical support contact Dmitriy Sklyar at [log in to unmask] or 847-509-9700 ext.311
##############################################################


ATOM RSS1 RSS2