Subject: | |
From: | |
Reply To: | TechNet E-Mail Forum. |
Date: | Thu, 30 Oct 2003 07:40:21 -0500 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
What does the internal die do to the test?
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Doug Pauls
> Sent: Wednesday, October 29, 2003 12:21 PM
> To: [log in to unmask]
> Subject: Re: [TN] IPC Cleaning Evaluation using B-36 coupons
>
>
> Jack,
> 1. Qualify the cleaning process to what standard? That
> may restrict
> what you can or cannot use as a component.
> 2. If you will be doing SIR testing, you have to make sure that the
> component package HAS NO INTERNAL DIE, or a true mechanical
> dummy. Many of the Practical Components or TopLine dummy
> components are packages with blown die, which can mess up
> SIR. Both companies do have these true dummies as available
> part numbers, but you may have to wait 6-8 weeks if they have
> to have them made for you. If you are doing only cleanliness
> testing, such as ROSE or IC, this distinction is irrelevant.
> 3. The B-36 board should come with solder mask on four
> points under the
> LCC which should give you a 5 mil standoff. You can have
> them made with thicker solder mask for greater standoff, but
> your solder volume may need to be increased, although the
> B-36 is not used as a solder demonstration platform. The
> PLCC is rather high in standoff. If you can find a gull wing
> with the proper I/O go for it.
> 4. The issue of whether the B-36 board is an accurate
> representation of
> product has always been a difficult one. The standard B-36
> has minimal solder mask and exposed metal, usually bare
> copper, under the components. Usually not indicative of
> actual product. Who are you trying to convince with the data?
>
> Doug Pauls
> Rockwell Collins
>
>
>
>
> Jack Evans
> <jack.evans@AEROF To:
> [log in to unmask]
> LEX.COM> cc:
> (bcc: Douglas O Pauls/CedarRapids/RockwellCollins)
> Sent by: TechNet Subject: [TN]
> IPC Cleaning Evaluation using B-36 coupons
> <[log in to unmask]>
>
>
> 10/29/2003 10:44
> AM
> Please respond to
> "TechNet E-Mail
> Forum."; Please
> respond to Jack
> Evans
>
>
>
>
>
>
> Hello,
> I am getting ready to qualify a new cleaning process using
> IPC B-36 test coupons and I am looking for suitable
> components for the test. The board was designed for the use
> of a 68 pin LCC or PLCC. The footprint is about .800 mils
> inside pad to pad square. The pad length is apx .100 mils.
> The problem with the components mentioned above are: The PLCC
> from Practical Components has a standoff height of about .020
> mils and the LCC fits tight to the board with no stand off at
> all. If I use the LCC I will likely fail the SIR testing
> because I don't think I can get under it to clean completely.
> If I use the PLCC, I will clean it ok, but I don't feel that
> it is a practical representation of what we see in
> production. I would really like to find a QFP that would fit
> this footprint and that I can form to a more realistic
> standoff height. Does anyone have any suggestions?
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
-----------------------------------------------------
|
|
|