TN strips off attachments. I'd suggest you sent the photo
Gary,
TN strips off attachments. I'd suggest you sent the photograph to Steve
(see Cc) and have him post it on his web site and that way those on TN
can view it.
Regards,
George
George M. Wenger
Senior Principle FMA / Reliability Engineer
Wireless network Solutions
Andrew Corporation, 40 Technology Drive, Warren, NJ 07059 (908) 546-4531
[log in to unmask]
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Bremer, Gary
Sent: Thursday, February 01, 2007 11:02 AM
To: [log in to unmask]
Subject: [TN] Mechanical Stress on solder joints
Gentlemen,
I have a device that failed in the field, the part is a DC/DC converter
that is first soldered to the circuit board then a massive heatsink is
screwed to the converter pulling the device upward because of an air gap
not covered by a thermal conductive pad. Could this be the cause of
damage to the component pins as shown in the attached photo? The solder
used is Sn63 on the circuit board side and the mass of the board solder
joint appears to be twice that of the component.
Gary Bremer
Senior Manufacturing Engineer, CIT
Curtiss-Wright Controls Inc.
Embedded Computing -Subsystem
28965 Avenue Penn
Santa Clarita, CA 91355-4185
Main: 661.257.4430 extension 2170
Fax: 661.257.4782
e-mail: [log in to unmask]
Web: www.cwcembedded.com
NOTICE: This e-mail communication is private and confidential and is
intended for the addressee only. The email may only be used for
conducting business with VISTA Controls Inc., dba Curtiss-Wright
Controls Embedded Computing Subsystems. If you are not the intended
recipient, please notify us by replying to this email followed by
deleting the email and all attachments from your system. Anyone other
than the intended recipient or those with a need to know within the
recipient's organization is strictly prohibited from using, printing,
distributing or disseminating the email or any information or attachment
contained therein.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
------------------------------------------------------------------------------------------------
This message is for the designated recipient only and may
contain privileged, proprietary, or otherwise private information.
If you have received it in error, please notify the sender
immediately and delete the original. Any unauthorized use of
this email is prohibited.
------------------------------------------------------------------------------------------------
[mf2]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|