At a company I used to work for they made simple small metal gauges
shaped like a letter H but with a very wide bar in the middle. The gap
on one side was .060" and the other was .045", but you can have them
made to whatever size you require. You can have any machine shop make
them. Be sure to have them completely deburred and hardened. The ones we
used were only about an inch wide and perhaps 1/2" tall.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Kathy Kuhlow
Sent: Tuesday, April 29, 2008 11:23 AM
To: [log in to unmask]
Subject: Re: [TN] gauges
I have always measured it off on a standard ruler and then put a tape
mark across the ruler. If the leads hit the tape it is over. Not too
scientific but it worked and didn't require additional gauge/calibration
costs. We periodically checked the mark.
Kat
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Linda Langley
Sent: Tuesday, April 29, 2008 9:31 AM
To: [log in to unmask]
Subject: [TN] gauges
I am looking for a company that would make gauges for measuring lead
lengths. .090 in and .085 in. Any suggestions would be greatly
appreciated.
Linda Langley
Jabil Circuit
Training Specialist
(248) 292-6176
CONFIDENTIALITY NOTICE: The information contained in this electronic
communication, including any attachments, is confidential information,
is intended only for the use of the recipients named above, and may be
legally privileged. If the reader of this message is not an intended
recipient, you are hereby notified that any review, use, dissemination,
distribution or copying of this communication, or any of its contents,
is strictly prohibited. If you have received this communication in
error, please notify us immediately of the error by return e-mail and
please permanently remove the original message and any copy of it from
your system. Nothing herein is intended to constitute an electronic
signature or consent. Thank you
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
