Unless you have some really gross deviations
If the deflections have affected paste print volume then probably you will
have reduced print efficiency/gasketing in some board areas and you will be
able to see this or have evidence from wipe frequency, backside smearing or
something. This could be reflected in the volume of solder on reflow, so you
might see this after reflow, [although the joints could be within acceptable
limits.]
If printing is not affected then the printed paste deposits will have the
same volume in deflected and non deflected areas. On reflow wetting and
surface tension forces should align the components to the same overall
height.
So: Do the different areas of the boards look the same?
Regards
Mike
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Hart, Dale L CTR USAF
AFMC AFRL/RXSA
Sent: Monday, October 04, 2010 7:26 PM
To: [log in to unmask]
Subject: [TN] pick and place /board deflection
I was on the shop floor and noticed deflection in the 8x8 inch panel that
was being populated. Would the deflection in the middle of the panel cause
components to sit higher on the paste and thus have a slightly higher solder
joint height than components on boards along the rails? Thanks in
advance
Dale L. Hart
Universal Technology Corporation (UTC)
Failure Analysis
1270 North Fairfield Road
Dayton, Ohio 45432-2600
(937) 656-9165
Fax (937) 656-4600
Email: <mailto:[log in to unmask]> [log in to unmask]
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
***This email, its content, and any files transmitted with it, are intended solely for the addressee(s) and may be legally privileged and/or confidential. If you are not the intended recipient, please contact the sender by return and delete the material from any computer. Any review, retransmission, dissemination, or other use of, or taking of any action in reliance upon this information by persons or entities other than the intended recipient is prohibited.
Messages sent via this medium may be subjected to delays, non-delivery, and unauthorized alteration. This email has been prepared using information believed by the author to be reliable and accurate, but Indium Corporation makes no warranty as to accuracy or completeness. Indium Corporation does not accept responsibility for changes made to this email after it was sent. Any opinions or recommendations expressed herein are solely those of the author. They may be subject to change without notice.***
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|