TECHNET Archives

December 2015

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Bhanu Sood <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Bhanu Sood <[log in to unmask]>
Date:
Tue, 1 Dec 2015 22:22:47 -0500
Content-Type:
text/plain
Parts/Attachments:
text/plain (88 lines)
From page 18 of 206:

"
At 2316:44 UTC, the sixth Master Caution triggered by AUTO FLT FAC 1 + 2
FAULT and followed by FDR signature of alteration of parameters of
components controlled by FAC 2 such as RTLU 2, Windshear Detection 2 and
Rudder Travel Limiter Actuator 2. The Auto Pilot (A/P) and the Auto-thrust
(A/THR) disengaged. Flight control law reverted from Normal Law to
Alternate Law. The aircraft started to roll to the left up to 54° angle of
bank. Nine seconds after the autopilot disengaged, the right side-stick
activated. The aircraft roll angle reduced to 9° left and then rolled back
to 53° left. The input on the right side-stick was mostly pitch* up and the
aircraft climbed up to approximately 38,000 feet with a climb rate of up to
11,000 feet per minute*.
"

From page 52 of 106

"
At 2317:41 U*TC the aircraft reached the highest altitude of 38,500 feet
(ISIS) and largest roll angle at 104° to the left. *The aircraft then
descended with a rate up to 20,000 feet per minute momentarily afterward
the rate of descent was recorded at average of 12,000 feet per minute until
the end of recording.
"

An ascent rate of 11000ft/min is highly unlikely on a commercial aircraft,
the CFM56-5B fans on this A320 most certainly were not designed to provide
such thrusts, at close to max takeoff weight. The most likely cause is an
extreme vertical wind shear (exceeding 10kt per 100ft) which caused a
vertical stall.
The solder-joints are a red herring IMHO..

Bhanu

On Tue, Dec 1, 2015 at 9:27 AM, Mike Buetow <[log in to unmask]>
wrote:

> Here's the report: http://kemhubri.dephub.go.id/knkt/ntsc_home/ntsc.htm
>
>
>
> Discussion of the electrical short and cracked solder joint begins on page
> 104.
>
>
>
>
>
> Best,
>
>
>
> Mike
>
>
>
> Mike Buetow
>
> PCD&F/Circuits Assembly
>
> w/m: 617-327-4702
>
> @mikebuetow
>
>
>
> The 2015 CIRCUITS ASSEMBLY *Directory of EMS Companies:*
> circuitsassembly.com/dems
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>



-- 
Bhanu Sood
Tel: (202) 468-8449

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

ATOM RSS1 RSS2