Thanks Stephen Joy,
Looks like Jack Olson was right. Looks like our suspicions were correct
also.
Again thanks to all.
Roberto Torres C.I.D.
Sr. PCB Designer
Matsushita Avionics Systems Corporation
-----Original Message-----
From: Joy, Stephen C [mailto:[log in to unmask]]
Sent: Friday, June 04, 1999 10:23 AM
To: [log in to unmask]
Subject: Re: [DC] Silkscreen feature in between fine
pitch
It's been a few years since I was in the screen print room,
but here is my
opinion.
The problem with legend ink dams are:
1. it is thermal, so where it lays is where it stays.
2. line width minimums are around .004-.005", less will give
skipping.
3. Legend ink bleeds. Depending on the ink viscosity, room
conditions and
curing characteristics you can add .002" to the line width.
4. If no mask on pad is the quality requirement, then the
registration
tolerance on a .020" pitch and .012" pad will be +/- .002"
for legend
printing.
Combine all of these variables and you have quality problem.
I doubt that
anyone is using this process, and if they are, ink on pads
is acceptable. If
they are and are using a photoimageable legend ink, they are
paying too much
for the boards.
If your process has solder bridging with nothing (or solder
mask) between
pads then there is another problem, and it isn't the pcb
design.
If ink on the pad is no issue, make it primary solder mask.
Design the mask
.008" wide for the .012" space. This will usually give clean
pads, but there
will be some low level of fallout, based on the process
controls of your
supplier. It may not be as thick as legend, but it will be
more reliable and
have comparable yields for bridging.
Steve
-----Original Message-----
From: Mike Gish [mailto:[log in to unmask]]
Sent: Friday, June 04, 1999 9:14 AM
To: [log in to unmask]
Subject: Re: [DC] Silkscreen feature in between fine pitch
The article was published in the June issue of Printed
Circuit Design. The
article is named "Being first
matters" Describes how Thomson Electronics uses several
methods to "do it
right the first time" etc.
Including software that allows for pitch compensation during
autoplacement.
Solder thieving pads for wave
solder, and silkscreen features on fine pitch components to
stop solder
bridging. (How they impliment this
is what we have all been trying to figure out) By the way
your questions
about registrations was my exact
question! You are right on target!
Mike Gish
Sr. PCB Designer
Ditron Manufacturing, Inc.
Phoenix, AZ
Jack Olson wrote:
> Well, not that my experience means anything, but I have
never seen that
> technique.
> I would think silkscreen registration is poor relative to
the small space
> between fine-pitch pads, and even a slight error will
screw up your
> assembly/soldering.
>
> I would like to know where that article was published,
> or hear from others who do it successfully.
>
> Jack
> (my employer stands behind every opinion I have....
<grin>)
>
> -----Original Message-----
> From: Roberto Torres
[mailto:[log in to unmask]]
> Re: Silkscreen feature in between fine
pitch
>
> No one else uses the below mentioned
silkscreen technique?
>
> On Wednesday, June 02, 1999 10:52 AM, Mike
Gish Wrote:
>
> I just finished reading an
article that
> described adding
> silksreen
> features in between pads
on fine pitch
> components to create
> an
> additional solder barrier
between pads.
> Does anyone have
> any experience
> doing this?
>
>
################################################################
> DesignerCouncil E-Mail Forum provided as a free service by
IPC using
LISTSERV 1.8c
>
################################################################
> To subscribe/unsubscribe, send a message to
[log in to unmask] with
following text in the body:
> To subscribe: SUBSCRIBE DesignerCouncil <your full name>
> To unsubscribe: SIGNOFF DesignerCouncil
>
################################################################
> Please visit IPC's web site (http://www.ipc.org) "On-Line
Services"
section for additional information.
> For technical support contact Hugo Scaramuzza at
[log in to unmask] or
847-509-9700 ext.312
>
################################################################
################################################################
DesignerCouncil E-Mail Forum provided as a free service by
IPC using
LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask]
with following
text in the body:
To subscribe: SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe: SIGNOFF DesignerCouncil
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line
Services" section
for additional information.
For technical support contact Hugo Scaramuzza at
[log in to unmask] or
847-509-9700 ext.312
################################################################
################################################################
DesignerCouncil E-Mail Forum provided as a free service by
IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask]
with following text in the body:
To subscribe: SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe: SIGNOFF DesignerCouncil
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line
Services" section for additional information.
For technical support contact Hugo Scaramuzza at
[log in to unmask] or 847-509-9700 ext.312
################################################################
################################################################
DesignerCouncil E-Mail Forum provided as a free service by IPC using LISTSERV 1.8c
################################################################
To subscribe/unsubscribe, send a message to [log in to unmask] with following text in the body:
To subscribe: SUBSCRIBE DesignerCouncil <your full name>
To unsubscribe: SIGNOFF DesignerCouncil
################################################################
Please visit IPC's web site (http://www.ipc.org) "On-Line Services" section for additional information.
For technical support contact Hugo Scaramuzza at [log in to unmask] or 847-509-9700 ext.312
################################################################
|