DDi bought Coretec.
DDi (Anaheim, CA) is a high tech PWB manufacturer, they should be able to do it.
Veronika Anderson, C.I.D.
Senior Electrical / Mechanical Designer
PerkinElmer Optoelectronics
1330 East Cypress St.,
Covina, CA 91724
Phone: (626) 967-9521 X 236
E-mail: [log in to unmask]
This email and any attachments thereto may contain private, confidential, privileged and ITAR controlled material for the sole use of the intended recipient. Any review, copying, or distribution of this email (or any attachments thereto) by others is strictly prohibited. If you are not the intended recipient, please contact the sender immediately and permanently delete the original and any copies of this email and any attachments thereto.
-----Original Message-----
From: DesignerCouncil [mailto:[log in to unmask]] On Behalf Of Andre Demers
Sent: Wednesday, July 14, 2010 1:40 PM
To: [log in to unmask]
Subject: Re: [DC] Looking for High Tech Board Shop - Chip-On-Board
Hi Dave,
I'm not sure, but I think that FTG or Coretec in Toronto have the capability to do what you need.
But where ever you end up getting the board made, expect to pay through the nose for the fab !
Good Luck.
Andre Demers C.I.D. +
Senior PCB Designer
cmrsummit Technologies
310-733 boulevard St-Joseph
Gatineau (Québec) J8Y 4B6
Canada
Telephone: 819.205.1185
Toll Free: 877.428.1229
Cell: 613.293.9723
[log in to unmask]
www.cmrsummit.com
-----Original Message-----
From: DesignerCouncil [mailto:[log in to unmask]] On Behalf Of David Baldwin
Sent: Wednesday, July 14, 2010 4:35 PM
To: [log in to unmask]
Subject: [DC] Looking for High Tech Board Shop - Chip-On-Board
DC Members:
I am looking for a high tech board shop that can manufacture a very tight PCB.
I am designing a PCB that has a Chip-On-Board. It has 568 pads, all
jammed on two sides. These all need to be wire bonded to the PCB
onto a 3-row configuration. It's far from ideal, but it is what I
have to work with. As a result, I am using a 12 mil via with a 6 mil
drill near the bond pads. Blind / buried vias are not practical for
this design. I can't make this 4 rows or spread things out any
further as we will exceed the capabilities of the wire bonder.
This design has 3 mil trace / space.
100 ohm differential pairs.
12 layers.
0.048" thick.
12 mil via, 6 mil drill.
Any recommendations for a board shop that can do something like this
would be greatly appreciated.
Thanks,
David Baldwin
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
|