Forwarding a couple of opportunities for a PCB Designer in the San Diego
area...
contact information is:
Cherelle Jacinto
Technical Recruiter- AEROTEK
(619) 278-3008
[log in to unmask]
See job descriptions below...
-----Original Message-----
From: Jacinto, Cherelle [mailto:[log in to unmask]]
Sent: Monday, March 27, 2006 2:01 PM
To: Brooks,Bill
Subject: RE: PCB designer opportunity
This one is in the Miramar area. Salary $70-80K.
The primary responsibilities for this position are as follows:
*Design the printed circuit boards as required. This will include high
volume production, low volume production and prototype work.
*Perform design reviews and analysis on printed circuit boards being
designed by partner companies.
*Work with Compliance Engineer to make sure designs meet agency
requirements.
*Develop new and innovative approaches to circuit layout.
The experience, knowledge and skills required are as follows:
*Associate Degree in a technical field plus at least 5 years of consumer PCB
design experience.
*Extensive training in CAD/Circuit Board design.
*Must be an expert in printed circuit board design, using the latest CAD
tools and layout packages including Power PC, PADS and OrCAD.
*Must have experience with Agile or OmniFi.
*Must be able to work with engineers to design boards with an emphasis in
routing for high speed digital data, signal integrity, EMC and safety agency
requirements.
*Must be thoroughly familiar with circuit board manufacturer requirements
and tradeoffs in material and techniques .
*Should have a good understanding of board panelization and other PCB cost
saving techniques.
This one is in Poway. Salary $65-80K.
PCB Designer - Design a wide variety of PC boards. Primarily backplanes, but
some active circuit board layout will be required. Ensure that mechanical
interfaces, primary and secondary power distribution, safety, applicable
approvals, EMC, impedance, crosstalk and test are considered on every
design. Must be proficient with all aspects of Mentor tools including Design
Architect, Librarian, and Boardstation (Expedition is not considered
equivalent to board station). Fully conversant with all aspects of PCB
design including schematic capture, board layout and generation of full
manufacturing package. Highspeed board layout, particularly differential
signaling. BSEE/CS is preferred.
Cherelle Jacinto
Technical Recruiter
(619) 278-3008
From: Brooks,Bill [mailto:[log in to unmask]]
Sent: Monday, March 27, 2006 1:55 PM
To: Jacinto, Cherelle
Subject: RE: PCB designer opportunity
Send me the requirement and the location... I'll see what I can do.
Bill Brooks - KG6VVP
PCB Design Engineer, C.I.D.+, C.I.I.
Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510
Datron World Communications, Inc.
_______________________________________
San Diego Chapter of the IPC Designers Council
Communications Officer, Web Manager
http://dcchapters.ipc.org/SanDiego/
http://pcbwizards.com
-----Original Message-----
From: Jacinto, Cherelle [mailto:[log in to unmask]]
Sent: Monday, March 27, 2006 1:46 PM
To: [log in to unmask]
Subject: PCB designer opportunity
Bill,
Hello, my name is Cherelle Jacinto and I am a Technical Recruiter for
Aerotek, a national staffing firm. I was referred to you by a candidate I
have contacted for PCB Designer opportunities. I am seeking candidates with
Mentor experience including Architect, Librarian and Boardstation. He
mentioned that you belong to a user group where I might be able to find or
network for interested candidates with this experience. I also have another
position available that requires ORCAD and PowerPCB experience and both
positions are permanent positions. I could send you job descriptions or
stop by to talk with your group.
If you may be of any assistance to me, I would appreciate it.
Thank you,
Cherelle
Cherelle Jacinto
Technical Recruiter
(619) 278-3008
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
|
