George:
Nice calculator, good job. The via though is just a via,
correct? It doesn't have anything for thermals. Like Bill said, I
can add up the spokes and get the overall width and treat it like a
trace. Or I could just forget about the thermals and let the
assemblers deal with soldering the parts down, not the designers
problem right;-)
Thanks,
Dave
At 03:49 PM 5/8/2007, you wrote:
>http://www.pcb-designer.com/trace.html
>
>--
>George Patrick
>Tektronix, Inc.
>Central Engineering, EDS Applications Support
>P.O. Box 500, M/S 39-512
>Beaverton, OR 97077-0001
>* 503-627-5272 (voice) * 503-627-5587 (fax)
>http://www.tektronix.com http://www.pcb-designer.com
>
>"Off-Grid and Proud of it!"
>
>
>-----Original Message-----
>From: DesignerCouncil [mailto:[log in to unmask]] On Behalf Of
>Brooks,Bill
>Sent: Tuesday, May 08, 2007 15:39
>To: [log in to unmask]
>Subject: Re: [DC] Current Capacity of Thermal Reliefs
>
>
>Dave,
>
>You will find the formulas for isothermal relief for through hole lands
>in
>the IPC-2222 section 9.1.2 Thermal Relief in Conductor Planes.
>
>Basically it tells you to use 60% of the land size as the 'thermal
>width'
>and then divide it up equally by however many ties you require. The gap
>between the pad and the plane can typically be near the same width as
>the
>web connection width unless you are dealing with some voltage spacing to
>another conductor which is a different matter all together.
>
>Regarding the current... if you have four .025 in. wide ties to a land,
>you
>would add them together to be equivalent to a .100 in. trace. Figure out
>what the current carrying capacity is for a .100 in. trace of the copper
>at
>the thickness you are using and you will be very close.
>
>Also the copper in the hole, if that is your application, can be
>calculated
>by converting the hole into a trace... just imagine splitting the barrel
>of
>the hole longwise and flattening it out... you then have a sheet of
>copper
>equivalent to the width and length of the rectangle by the thickness of
>the
>plating in the hole... It's not really rocket science... but you do have
>to
>use Pi in the calculation. :)
>
>I don't know of a calculator for that task but is sounds like a great
>project. Any ambitious programmers out there want to take it on?
>
>Best regards,
>
>Bill Brooks
>PCB Design Engineer, C.I.D.+
>Tel: (760)597-1500 Fax: (760)597-1510
>Datron World Communications, Inc.
>Vista, California
>
>
>-----Original Message-----
>From: David Baldwin [mailto:[log in to unmask]]
>Sent: Tuesday, May 08, 2007 2:35 PM
>To: [log in to unmask]
>Subject: [DC] Current Capacity of Thermal Reliefs
>
>Is there a calculator for the current carrying capacity of a
>component thermal relief?
>
>Thanks,
>
>Dave
>
>------------------------------------------------------------------------
>----
>-----
>DesignerCouncil Mail List provided as a free service by IPC using
>LISTSERV
>1.8d
>To unsubscribe, send a message to [log in to unmask] with following text
>in
>the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
>To temporarily stop/(restart) delivery of DesignerCouncil send: SET
>DesignerCouncil NOMAIL/(MAIL)
>Search previous postings at: www.ipc.org > On-Line Resources & Databases
> >
>E-mail Archives
>Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16
>for additional information, or contact Keach Sasamori at [log in to unmask]
>or
>847-615-7100 ext.2815
>------------------------------------------------------------------------
>----
>-----
>
>------------------------------------------------------------------------
>---------
>DesignerCouncil Mail List provided as a free service by IPC using
>LISTSERV 1.8d
>To unsubscribe, send a message to [log in to unmask] with following text
>in
>the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
>To temporarily stop/(restart) delivery of DesignerCouncil send: SET
>DesignerCouncil NOMAIL/(MAIL)
>Search previous postings at: www.ipc.org > On-Line Resources & Databases
> > E-mail Archives
>Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
>information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
>ext.2815
>------------------------------------------------------------------------
>---------
>
>---------------------------------------------------------------------------------
>DesignerCouncil Mail List provided as a free service by IPC using
>LISTSERV 1.8d
>To unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
>To temporarily stop/(restart) delivery of DesignerCouncil send: SET
>DesignerCouncil NOMAIL/(MAIL)
>Search previous postings at: www.ipc.org > On-Line Resources &
>Databases > E-mail Archives
>Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
>information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815
>---------------------------------------------------------------------------------
________________________________________________________
We make a Living by what we get, We make a Life by what we give.
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
|
