Subject: | |
From: | |
Reply To: | (Designers Council Forum) |
Date: | Thu, 28 Feb 2002 08:42:22 -0600 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
"Gillan, David M (FL51)" wrote:
> Good morning all,
>
> I have a small problem and can not figure out how to solve it. Here is some
> background. We have received marching orders to send all of our Circuit
> Card Assembly (CCA) out of house to be built. It is to be done in Minnesota
> now. We must supply this vendor with all updated data files as well as an
> updated assembly drawing. We must include a view of each unique dash
> numbered assembly in the assembly drawing. We have instituted the use of
> variants in our designs to help facilitate this. That part is fairly easy.
> Here's my problem. I have a CCA with a -001 and -002 assembly. the -002 is
> the current active assembly. The -001 was inactivated about 2 years ago and
> is not built any more. However, we have some of these boards in the field,
> so we must document this configuration. These two dash numbered assemblies
> are different. The -002 was made to incorporate design changes. I need to
> bring in a copy of the old -001 and drop this view on a sheet of the
> assembly. Mentor will only allow a design to have one board geometry. Is
> there any way I can convert the -001 board, with components placed, into a
> generic or other type of geom? At the moment I am creating a generic unique
> geom for this -001 assembly by tracing the outlines of the board and
> components and putting these lines and arcs on layer drawing_1. This is
> very tedious and time consuming. If this was to be the only board that
> would need to be done I would not ask for any help; however, there will be
> many more just like this. If anyone has some suggestions they will be
> greatly appreciated.
>
> Dave
>
> <<...OLE_Obj...>>
> Honeywell
>
> David M. Gillan Sensor and Guidance Products
> Guidance and Navigation Operation
> LMS Librarian CAD Design Center
> CAD Coordinator
> Work Director
>
> 727 539-4420 VOX
> 727 539-4991 Fax
> [log in to unmask]
>
> ---------------------------------------------------------------------------------
> DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
> To set a vacation stop for delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL
> Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
> Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
> information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
> ------------------------------------------------------------------------------
Have you tried using the Detailed View command in Fablink. This can make a snapshot of your
board geometry window into a generic geometry which then can be put into your drawing. Of
course,
it isn't dynamic and must be regenerated every time there is a change.
John Bradley
Alcatel USA
Plano, TX
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To set a vacation stop for delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
---------------------------------------------------------------------------------
|
|
|