Subject: | |
From: | |
Reply To: | (Designers Council Forum) |
Date: | Wed, 23 Oct 2002 15:06:00 +0100 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Is there any benefit to using these as opposed to a zero ohm jumper?
Perhaps in current handling?
> -----Original Message-----
> From: Rose, Steven M [SMTP:[log in to unmask]]
> Sent: Wednesday, October 23, 2002 2:45 PM
> To: [log in to unmask]
> Subject: Re: [DC] SMT Jumpers
>
> http://www.componentscorp.com/Addon/sj_1206/sj_1206.html
> Steve Rose
> Senior PCB Design Engineer
>
> Corning Incorporated EPP
> 21 Lynn Morse Drive
> SP-ZV-00-A24B
> Painted Post, New York 14870
>
>
> Work: 607 974-1791
> Cell: 607 765-0229
>
>
>
>
> > ----------
> > From: Volkmar Huss[SMTP:[log in to unmask]]
> > Reply To: (Designers Council Forum);Volkmar Huss
> > Sent: Wednesday, October 23, 2002 9:28 AM
> > To: [log in to unmask]
> > Subject: Re: [DC] SMT Jumpers
> >
> > Mark Mainland wrote:
> >
> > >
> > >
> > > Hello,
> > > I've got a board that needs to be routed on a single side, I'm looking
> > > for some SMT jumpers that come on tape & reel. I have looked at
> > > Zierick but they only have a .300" & 1.5" size, does anybody have a
> > > source that has more sizes available?
> > >
> > > Thanks.
> > >
> >
> > We have used 0 Ohm MELF resistors of 0204 or 0207 (metric) size. They
> are available on tape & reel.
> >
> > You can route traces between pads. Zero Ohm 1206 chip resistors should
> work, too.
> >
> > See http://www.bccomponents.com/Uploads/Datasheets/melpro.pdf on page 2
> bottom right.
> >
> > Best regards
> >
> > Volkmar Hu> ß C.I.D.
> >
> > Engineering Electronic Circuit Boards
> > Aufbau- und Verbindungstechnik
> > _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
> >
> > DRÄGER ELECTRONICS
> >
> > Draeger Electronics GmbH
> > Moislinger Allee 53-55
> > D-23558 Lübeck
> >
> > Tel: +49-451-882-3998
> > Fax: +49-451-882-4365
> > mailto:[log in to unmask]
> > Website http://www.draeger-electronics.com
> > _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
> >
> > Important Notice
> > This email and any attachment hereto are confidential and may contain
> trade
> > secrets or may be otherwise protected from disclosure. If you have
> received
> > it in error you are in notice of this fact. Please notify us immediately
> by
> > reply email and then delete this email and any attachment from your
> system.
> > Please understand that you are not allowed to copy this email or any
> > attachment hereto or disclose its contents to any other person. Thank
> you.
> >
> >
> >
>
> --------------------------------------------------------------------------
> -------
> DesignerCouncil Mail List provided as a free service by IPC using LISTSERV
> 1.8d
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
> To set a vacation stop for delivery of DesignerCouncil send: SET
> DesignerCouncil NOMAIL
> Search previous postings at: www.ipc.org > On-Line Resources & Databases >
> E-mail Archives
> Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
> information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700
> ext.5315
> --------------------------------------------------------------------------
> -------
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To set a vacation stop for delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/html/forum.htm for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-509-9700 ext.5315
---------------------------------------------------------------------------------
|
|
|